Cat C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD
IMAGES PREVIEW OF THE MANUAL:
DESCRIPTION:
Cat C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD
1YN1-Up (Engine)
2PN1-Up (Engine)
Important Safety Information :
Most accidents that involve product operation, maintenance and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills and tools to perform these functions properly.
- Improper operation, lubrication, maintenance or repair of this product can be dangerous and couldresult in injury or death. Do not operate or perform any lubrication, maintenance or repair on this product, until you have readand understood the operation, lubrication, maintenance andrepair information. Safety precautions and warnings are provided in this manual and on the product.
- If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. The hazards are identified by the “Safety Alert Symbol” and followed by a “Signal Word” such as “DANGER”, “WARNING” or “CAUTION”. The Safety Alert “WARNING” label is shown below.
TABLE OF CONTENTS:
Cat C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD
Disassembly andAssembl y Section
Summary of Revisions 4
Fuel Priming Pump – Remove and Install 4
Fuel Filter Base – Remove and Install 5
Fuel Transfer Pump – Remove 7
Fuel Transfer Pump – Install 7
Fuel Manifold – Remove 7
Fuel Manifold – Install 8
Electronic Unit Injector – Remove 9
Electronic Unit Injector – Install 10
Electronic Unit Injector Sleeve – Remove 12
Electronic Unit Injector Sleeve – Install 12
Turbocharger – Remove 13
Turbocharger – Install 14
Exhaust Manifold – Remove and Install 15
Inlet Manifold – Remove 15
Inlet Manifold – Install 16
Inlet and Exhaust Valve Springs – Remove and
Install 16
Inlet and Exhaust Valves – Remove and Install 19
Inlet and Exhaust Valve Guides – Remove and
Install 20
Inlet and Exhaust Valve Seat Inserts – Remove and
Install 21
Engine Centrifugal Oil Filter – Remove and
Install 22
Engine Oil Filter Base – Remove 25
Engine Oil Filter Base – Disassemble 26
Engine Oil Filter Base – Assemble 27
Engine Oil Filter Base – Install 28
Engine Oil Cooler – Remove 29
Engine Oil Cooler – Install 30
Engine Oil Pump – Remove 31
Engine Oil Pump – Disassemble 32
Engine Oil Pump – Assemble 33
Engine Oil Pump – Install 33
Water Pump – Remove 34
Water Pump – Disassemble 35
Water Pump – Assemble 38
Water Pump – Install 40
Water Temperature Regulator – Remove and Install
41
Water Outlet Manifold – Remove 44
Water Outlet Manifold – Install 45
Flywheel – Remove 45
Flywheel – Install 46
Crankshaft Rear Seal – Remove 46
Crankshaft Rear Seal – Install 47
Crankshaft Rear Seal Carrier – Remove and
Install 48
Flywheel Housing – Remove and Install 49
Rear Power Take-Off (RPTO) – Remove 50
Rear Power Take-Off (RPTO) – Install 52
Vibration Damper and Pulley – Remove and Install
55
Crankshaft Front Seal – Remove 56
Crankshaft Front Seal – Install 56
Front Cover – Remove 57
Front Cover – Install 58
Gear Group (Front) – Remove 58
Gear Group (Front) – Install 59
Housing (Front) – Remove 61
Housing (Front) – Install 61
Accessory Drive – Remove 64
Accessory Drive – Disassemble 64
Accessory Drive – Assemble 65
Accessory Drive – Install 66
Valve Mechanism Cover – Remove and Install 66
Valve Mechanism Cover Base – Remove and
Install 67
Compression Brake – Remove 68
Compression Brake – Disassemble 69
Compression Brake – Assemble 72
Compression Brake – Install 76
Rocker Shaft and Pushrod – Remove 76
Rocker Shaft – Disassemble 77
Rocker Shaft – Assemble 78
Rocker Shaft and Pushrod – Install 78
Cylinder Head – Remove 79
Cylinder Head – Install 81
Lifter Group – Remove and Install 84
Camshaft – Remove 86
Camshaft – Install 87
Camshaft Gear – Remove and Install 88
Camshaft Bearings – Remove 89
Camshaft Bearings – Install 90
Engine Oil Pan – Remove and Install 90
Cylinder Liner – Remove 92
Cylinder Liner – Install 93
Piston Cooling Jets – Remove and Install 94
Pistons and Connecting Rods – Remove 95
Pistons and Connecting Rods – Disassemble 96
Pistons and Connecting Rods – Assemble 97
Pistons and Connecting Rods – Install 98
Connecting Rod Bearings – Remove 100
Connecting Rod Bearings – Install 100
Crankshaft Main Bearings – Remove 101
Crankshaft Main Bearings – Install 102
Crankshaft – Remove 104
Crankshaft – Install 104
Crankshaft Gear – Remove and Install 105
Bearing Clearance – Check 107
Coolant Temperature Sensor – Remove and
Install 108
Engine Oil Pressure Sensor – Remove and Install
109
Speed/Timing Sensor – Remove and Install 109
Belt Tensioner – Remove and Install 111
Engine Control Module – Remove and Install 112
Alternator – Remove and Install 113
Electric Starting Motor – Remove and Install 114
Air Conditioner Support Bracket – Remove and
Install 114
Air Compressor – Remove and Install 115
Air Compressor Drive Gear – Remove 117
Air Compressor Drive Gear – Install 117
Index Section
Index 119
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the SAME exact manual used by your dealers to fix your vehicle.
- The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
- Any queries / doubts regarding your purchase, please feel free to contact [email protected]
S.V