Fassi Crane F 330D 360DXP.24 Use and Maintenance Manual
FILE DETAILS:
Fassi Crane F 330D 360DXP.24 Use and Maintenance Manual
Language : English
Pages : 104
Downloadable : YES
Format : PDF
Size : 2.96 MB
Serial No : *6001*
DESCRIPTION:
Fassi Crane F 330D 360DXP.24 Use and Maintenance Manual
INTRODUCTION:
The fitment of the crane on the vehicle must be carried out in accordance with the instructions given by FASSI in the manual for hydraulic crane fitting and the relevant chassis manufacturers directives. The Manufacturer declines all responsibility and guarantee if the fitting is entrusted to workshops without sufficient technical capability to carry out the work in conformity. Be sure that the unit has been installed, inspected and tested in accordance with the local legal requirements.
- As well as the principal safety norms, this manual contains a description of the crane and the instructions for use and maintenance. The following instructions refer to mobile cranes in general and must be integrated with the manual for use supplied by the centre responsible for the crane fitting on truck, vehicle or other type of structure.
- READ THIS MANUAL CAREFULLY prior to use or any maintenance. A few minutes spent now could save time and labour later. Always conform to the safety norms and the instructions for use and maintenance contained in the present manual in order to guarantee a long life to the crane.
TABLE OF CONTENTS:
Fassi Crane F 330D 360DXP.24 Use and Maintenance Manual
INDEX
1 INTRODUCTION
2 CLASSIFICATION OF THE CRANE MODEL
2.1 Generality
2.2 Hydraulic jibs
2.3 Technical data
3 CAPACITY PLATES
3.1 Generality
3.2 Capacity plates with lifting moment limiting device
4 HYDRAULIC SCHEMATICS (version with lifting moment limiting device) ( )
5 ELECTRIC SCHEMATICS (version with lifting moment limiting device) ( )
6 SAFETY NORMS
7 WARNING AND INSTRUCTIONS
7.1 Generality
7.2 Before operating
7.3 During operation
7.4 At the end of the operation (Prior to driving the vehicle)
7.5 Residual risks
8 IDENTIFICATION OF THE CRANE MODEL
8.1 Generality
8.2 Crane mark
9 CRANE NOMENCLATURE
9.1 Crane with distributor on the column
9.2 Crane with ground controls on both sides
Crane with ground controls on both sides and with top seat controls by hand cables
9.3 Crane with top seat controls and with ground controls for outriggers
10 NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES
10.1 Crane with distributor on the column
11 SUPPLEMENTARY BEAMS
11.1 Generality
11.2 Identification of the supplementary beams
12 TILTABLE OUTRIGGER RAMS (not available)
13 MANOEUVRES AND CONTROLS TO STABILIZE THE VEHICLE
13.1 Generality
13.2 Functions of control levers for stabilization with horizontal distributor
13.2.1 Functions of control levers for stabilization with vertical distributor
13.3 Controls to stabilize the vehicle
13.4 Manualy tiltable outrigger rams
13.5 Crane with hydraulic tiltable supports (with hydraulic motor) for outrigger rams
14 CONTROLS TO OPERATE THE CRANE
14.1 Generality
Edition 04.10.2006
14.2 Radio-remote control
14.2.1 Use of the radio-remote control
14.2.2 Push-button panel of the radio remote control “RCH”
14.2.3 Icon legend valid for the display of both radio-remote control panel (GUI ver 002)
14.3 Emergency station from the column (if accessible)
14.4 Manoeuvres to unfold the crane into a working condition
14.5 Manoeuvres to fold the crane into the rest condition
14.6 Manoeuvres to unfold the crane “C” into a working condition (only for the crane version C)
14.7 Manoeuvres to fold the crane “C” into the rest condition (only for the crane version C)
14.8 Indicator of inner boom horizontal position (on request)
15 MANOEUVRES OF THE CRANE LOADS (version with load limiting device)(not available)
16 MANOEUVRES OF THE CRANE LOADS (version with lifting moment limiting device) ( )
16.1 Generality
16.2 Lifting moment limiting device “EVOLUTION” (LMEV) and automatic dynamic control (ADC)
16.3 Control panels of the lifting moment limiting device (if fitted)
16.4 Load handling
16.4.1 “Block due to overload condition”
16.4.2 “Winch off” (when fitted)
16.4.3 “Lifting block” (Pro link)
16.4.4 Other functional characteristics
16.4.5 Visual indicator yellow/red light
16.5 Lifting moment limiting device for two working sectors
16.6 Rotation limiting device
16.7 Setting menu
16.8 Diagnostic: alarms and warnings
16.8.1 Emergency control station on the column and exclusion tap lever
16.9 XP device
16.9.1 Activation and instructions for use of the XP/CR device
17 USE OF IMPLEMENTS
17.1 Generality
17.2 Hydraulic connections for implements – supplementary hoses
17.3 Oil cooler (heat exchanger)
18 MANUAL EXTENSIONS
18.1 Generality
18.2 Lifting moment limiting device “ELECTRONIC” for the manual extensions (see “Setting Menù”)
19 CONTROLS TO OPERATE THE HYDRAULIC IMPLEMENTS OF THE CRANE
20 HYDRAULIC JIBS
20.1 Generality
20.2 Identification of the hydraulic jib
20.3 Nomenclature of the hydraulic jib
20.4 Ma no e u vres to un fold the jib in wor king con di tion
20.5 Ma no e u vres to fold the jib in rest con di tion
20.6 O pe ra tions to re mo ve the hy dra u lic jib from the cra ne
20.7 O pe ra tions to mount the hy dra u lic jib on the cra ne
20.8 Hydraulic jib articulated at 25 degrees with the automatic control (L515-L516)(not available)
20.9 Use of the hydraulic jib articulated at 25 degrees (not available on the L102 and on the L515-L516)
20.10 Crane with lifting moment limiting device and “Pro link” (if fitted)
21 WINCH (if fitted)
21.1 Generality (version with lifting moment limiting device)
21.2 Winch for crane (version with lifting moment limiting device)
21.2.1 Winches equipped with a mechanical stroke end device (version with lifting moment limiting device)
22 MAINTENANCE INSTRUCTIONS
22.1 Generality
22.2 After every 8 working hours or at the end of every working day
22.3 After every 40 working hours or after every working week
22.4 After every 100 working hours or more frequently in case of more intensive utilisation
22.5 After every 500 working hours or after every 6 working months
22.6 After every 1000 working hours or after every working year
22.7 Complete overhaul of the crane is required when 10.000 working hours or 10 years’life are reached
22.8 Instructions for the dismantlement and the demolition of a FASSI crane
23 TABLE OF HYDRAULIC OIL AND LUBRICANTS CHA RAC TE RI STI CS
24 POSSIBLE FAULTS
24.1 Generality
24.2 Only operations which can be carried out by the user
24.3 Operations to be carried out only by a service center
25 INSTRUCTION AND WARNING PLATES
VIDEO PREVIEW OF THE MANUAL:
IMAGES PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the same manual used by the dealers to diagnose and troubleshoot your vehicle
- You will be directed to the download page as soon as the purchase is completed. The whole payment and downloading process will take anywhere between 2-5 minutes
- Need any other service / repair / parts manual, please feel free to contact [email protected] . We still have 50,000 manuals unlisted