Linkbelt 160X3 Excavator Service Manual WLSM1606-07LX – PDF DOWNLOAD
FILE DETAILS:
Linkbelt 160X3 Excavator Service Manual WLSM1606-07LX – PDF DOWNLOAD
Language : English
Pages : 1501
Downloadable : Yes
File Type : PDF
Size: 78.8 MB
IMAGES PREVIEW OF THE MANUAL:
VIDEO PREVIEW OF THE MANUAL:
DESCRIPTION:
Linkbelt 160X3 Excavator Service Manual WLSM1606-07LX – PDF DOWNLOAD
General Information:
Cleaning
Clean the metal parts with a cleaning fluid or steamer that meets standards. (except for the bearing) After cleaning the parts, let them dry well and inject oil into all parts. Inject oil into the bearing after letting it dry.
Inspection
When disassembling parts, inspect all the parts. Replace any worn or damaged parts. Inspect them thoroughly to prevent early failures.
Bearing
If the bearing is loose, replace it. Install the bearing after air drying it.
Needle bearing
When inserting the needle bearing, be careful not to scratch it.
Inject grease into the location where the needle bearing is to be inserted.
Gear
Check for any wear or damage.
Oil seals, O-rings, gaskets
Always install new oil seals, O-rings, and gaskets. Inject grease into the locations where oil seals and O-rings are to be inserted.
Shaft
Check for any wear or damage. Check the oil seal on the bearing and damaged shaft.
Service parts
Install genuine LBX Link-Belt service parts. When ordering parts, see the parts catalog that has genuine LBX Link-Belt part numbers listed. Any failures caused by installing a nongenuine part are not covered by the warranty.
Lubrication (fuel, hydraulic oil)
- Use oils from specified manufacturers or the ones specified in the operator’s manual or Service Manual.
- Any failures caused by using other fuel or hydraulic oil than specified are not covered by the warranty.
TABLE OF CONTENTS:
Linkbelt 160X3 Excavator Service Manual WLSM1606-07LX – PDF DOWNLOAD
Excavator 1
SAFETY 7
Safety, general information and standard torque data 10
General Information 11
Safety 11
ROPS 14
ROPS Judgment Method 14
Standard Torque Data For Cap Screws And Nuts 19
Bolt and Nut Tightening 19
A LOWER 21
Main Equipment Table 25
160X3 25
Lower Component 25
Travel Unit 25
Take-up Roller 25
Upper Roller 25
Lower Roller 25
Recoil Spring 25
Shoe 26
Center Joint 26
Main Equipment Structure and Operation Explanation 27
Travel Motor 27
Travel motor operation explanation 27
Port Diagram 41
Travel Motor 41
Center Joint 41
Basic Functions 42
Travel Speed Selection 42
Travel Alarm 43
Removal and Installation of Track 45
Removal and Installation of Shoe Assembly 45
Removal of Shoe Assembly 45
Installation of Shoe Assembly 46
Removal and Installation of Shoe Plate 48
Removal of Shoe Plate 48
Installation of Shoe Plate 48
Precautions for Shoe Bolt Installation 48
Removal and Installation of Roller 50
Removal and Installation of Upper Roller 50
Removal of Upper Roller 50
Installation of Upper Roller 51
Assembly and Disassembly of Upper Roller 52
Configuration Diagram 52
Dimension Diagram 53
Jig Dimension Diagram 53
Disassembly Procedures 54
Assembly Procedures 56
Removal and Installation of Lower Roller 58
Removal of Lower Roller 59
Installation of Lower Roller 59
Assembly and Disassembly of Lower Roller 60
Configuration Diagram 61
Dimension Diagram 61
Jig Dimension Diagram 62
Disassembly Procedures 62
Assembly Procedures 64
Removal and Installation of Drive Sprocket 67
Removal of Drive Sprocket 67
Installation of Drive Sprocket 68
Removal and Installation of Take-up Roller 69
Removal of Take-up Roller 69
Installation of Take-up Roller 70
Assembly and Disassembly of Take-up Roller 71
Configuration Diagram 72
Dimension Diagram 72
Jig Dimension Diagram 73
Disassembly Procedures 73
Assembly Procedures 76
Removal and Installation of Grease Cylinder 79
Removal of grease cylinder 79
Installation of grease cylinder 80
Assembly and Disassembly of Tension Shock Absorber 81
Configuration Diagram 81
Dimension diagram 81
Jig dimension diagram 82
Disassembly procedures 82
Assembly procedures 82
Removal and Installation of Center Joint 84
Removal of Center Joint 84
Installation of Center Joint 86
Assembly and Disassembly of Center Joint 88
Configuration Diagram 89
Dimension Diagram 90
Jig Dimension Diagram 91
Disassembly Procedures 91
Assembly Procedures 92
Removal and Installation of Travel Motor 95
Removal of Travel Motor 95
Installation of Travel Motor 97
Assembly and Disassembly of Travel Motor 100
Tools for Assembly and Disassembly 100
Standard tools 100
Secondary materials 101
Special tools 102
Measurement device 102
Motor Disassembly Procedures 103
Precautions before motor disassembly 103
Tightening torque 104
Disassembly procedure 105
Maintenance Standards 114
Motor parts maintenance standards 114
Reduction gear parts maintenance standards 117
Motor Assembly Procedures 120
Precautions before motor assembly 120
Assembly procedures 121
Installation of Motor 133
Motor inspection 133
Operation Check 135
Motor operation check 136
Troubleshooting 137
Motor Repair Kit 145
Travel Motor Internal Structure Diagram 148
Travel Motor Part Table 150
Maintenance Standards 152
Drive sprocket 152
Take-up roller 153
Upper roller 154
Lower Roller 155
Track Shoe (grouser shoe) 156
Inspection Gauge 158
For Drive Sprocket 158
For Take-up Roller 158
For Upper Roller 159
For Lower Roller 159
Pressure Measurement and Adjustment Procedures 160
Main Pressure Measurement 160
B Travel Pressure Measurement 160
Drain Volume Measurement Procedures 161
Preparations 161
Travel Motor Drain Volume Measurement 161
Air Bleed Procedure 163
Travel Motor 163
Check 163
B C SWING UNIT, COUNTERWEIGHT 165
Main Equipment Table 168
160X3 168
Upper Component 168
Swing Unit 168
Main Equipment Structure and Operation Explanation 169
Swing Motor 169
Equipment configuration 169
Internal Structure Diagram 172
Swing reduction gear internal structure diagram 173
Relief valve internal structure diagram 173
Swing Motor Part Table 174
Port Diagram 175
Swing Motor 175
Basic Functions 176
Swing Brake 176
Swing Lock 177
Swing Speed Limit 178
Free Swing (option) 179
Removal and Installation of Swing Unit 180
Removal of Swing Unit 180
Installation of Swing Unit 182
Assembly and Disassembly of Swing Motor 183
Causes of Trouble and Solutions 183
Maintenance Standard Table 185
Jig 186
Disassembly 187
Assembly 192
Swing Motor Internal Structure Diagram 202
Assembly and Disassembly of Swing Unit 204
Disassembly 204
Assembly 205
Assembly and Disassembly of Swing Reduction Gear 207
Disassembly 207
Assembly 210
Jig 216
Swing Reduction Gear Structure Diagram 217
Removal and Installation of Counterweight 218
Removal of Counterweight 218
Installation of Counterweight 219
Pressure Measurement and Adjustment Procedures 221
Main Pressure Measurement 221
C Swing Pressure Measurement 221
Drain Volume Measurement Procedures 222
Preparations 222
Swing Motor Drain Volume Measurement 222
Air Bleed Procedure 223
Swing Motor 223
Check 223
H ENGINE 225
Main Equipment Table 230
160X3 230
Engine-related 230
Engine 230
DPD 230
Air Cleaner (double element) 230
Radiator 230
Basic Functions 231
Fuel Gauge 231
Coolant Temperature Gauge 233
DPD Gauge 235
Fuel Economy Gauge 236
Neutral Start 237
Engine Start/Stop Control 238
Power-cut Delay 239
Preheating 240
Throttle 241
Engine Throttle Switch Position Detection 242
Idling Start 248
Auto Idle 249
One-touch Idle 250
Auto Warm Up 251
Quick Warm Up 252
Idling Stop 254
Idle up 255
Work Mode Control 256
Engine Emergency Stop 258
Coolant Level Reduction 258
Engine Air Filter Clog 259
Fuel Filter Clog 260
DPD Regeneration 261
Automatic Regeneration 263
Manual Regeneration 265
Optional Manual Regeneration 268
Hydraulic Assisting Load 270
Primary specifications 271
Function, Structure, and Operations 273
Symptom 315
Frequent Manual DPD Regeneration 315
DPD Regeneration Taking Excessively Long 316
Engine Start Problems 317
Engine Stalling 319
Engine Hunting, Rough Idling 321
Excess Amount of White Smoke in Exhaust Gas 323
Excess Amount of Black Smoke in Exhaust Gas 323
Abnormal Noise 324
Large fuel consumption 325
Large oil consumption 326
Engine Output Deficiency 327
Functional Inspection 329
Inspection of the starter circuit system 329
Compression pressure inspection 329
Starting System Inspection 330
Inspection of the fuel system 331
Inspection of the air intake system 332
Inspection of the exhaust system 332
Inspection of EGR Control System 332
Inspection of the glow control system 333
DPD Function Inspection 334
OBD System Check 336
Inspection of the monitor warning light illumination circuit system 337
Inspection of the monitor warning light blinking circuit system 337
Inspection of Scan Tool Power Supply System 338
Maintenance precautions 339
Removal and Installation of Engine Assembly 342
Removal of Engine Assembly 342
Installation of Engine Assembly 346
Removal and Installation of Fuel Cooler, Engine Intercooler, Radiator, and Oil Cooler 347
Removal and Installation of Fuel Cooler 347
Removal of Fuel Cooler 347
Installation of Fuel Cooler 347
Removal and Installation of Engine Intercooler 347
Removal of Intercooler 348
Installation of Inter Cooler 348
Removal and Installation of Radiator 349
Removal of Radiator 349
Installation of Radiator 352
Removal and Installation of Oil Cooler 352
Removal of Oil Cooler 352
Installation of oil cooler 354
Removal and Installation of Turbo Charger 355
Turbocharger assembly Removal 355
Turbocharger assembly Installation 356
Removal and Installation of EGR Valve 358
Removal and Installation of EGR Cooler 358
EGR cooler Removal 358
EGR cooler Installation 358
Removal and Installation of EGR Valve (if equipped) 359
EGR valve Removal 359
EGR valve Installation 360
Removal and Installation of Engine Hood 361
Removal of Engine Hood 361
Installation of Engine Hood 362
Removal and Installation of Muffler 363
Removal of Muffler 363
Installation of Muffler 363
Removal and Installation of Cylinder Head Cover 365
Cylinder head cover Removal 365
Installation of Cylinder Head Cover 366
Removal and Installation of Cylinder Head 367
Removal of Cylinder Head 367
Disassembly of Cylinder Head 375
Assembly of Cylinder Head 377
Installation of Cylinder Head 380
Inspection 397
Removal and Installation of Cylinder Block 403
Removal of Cylinder Block 403
Installation of Cylinder Block 419
Inspection of Cylinder Block 450
Lubrication System 452
Removal and Installation of Oil Pan and Crank Case 452
Removal of Oil Pan and Crank Case 452
Disassembly of Oil Pan and Crank Case 466
Assembly of Oil Pan and Crank Case 467
Installation of Oil Pan and Crank Case 467
Removal and Installation of Oil Pump Assembly 493
Removal of Oil Pump Assembly 493
Installation of Oil Pump Assembly 496
Inspection of Oil Pump Assembly 499
Engine oil Inspection 500
Cooling System 501
Removal and Installation of Water Pump Assembly 501
Removal of Water Pump Assembly 501
Installation of Water Pump Assembly 502
Inspection of Water Pump Assembly 503
Removal and Installation of Thermostat 504
Removal of Thermostat 504
Installation of Thermostat 504
Inspection 504
InspectionInspection of Coolant 505
Inspection of Cooling Fan Belt 506
Removal and Installation of Exhaust Manifold 507
Removal of Exhaust Manifold 507
Installation of Exhaust Manifold 508
Inspection of Exhaust Manifold 511
Disassembly, Removal and Installation of DPD Assembly 512
Disassembly of DPD Assembly 512
Assembly of DPD Assembly 513
Inspection 516
Removal and Installation of Fuel Tank 517
Removal of Fuel Tank 517
Installation of Fuel Tank 519
Removal and Installation of Fuel Supply Pump 520
Removal of Fuel Supply Pump 520
Installation of Fuel Supply Pump 525
Removal and Installation of Common Rail Assembly 533
Removal of Common Rail Assembly 533
Installation of Common Rail Assembly 534
Removal and Installation of Injector 536
Removal of Injector 536
Installation of Injector 538
Removal and Installation of Starter Motor 541
Removal of Starter Motor 541
Installation of Starter Motor 541
Removal and Installation of Alternator 542
Removal of Alternator 542
Installation of Alternator 542
Preheating System 543
Removal and Installation of Glow Plug 543
Removal of Glow Plug 543
Installation of Glow Plug 543
Inspection of Glow Plug 544
Introduction to the trouble diagnosis 545
Removal and Installation of Suction Control Valve 554
Removal of Suction Control Valve 554
Installation of Suction Control Valve 554
Removal and Installation of Fuel filter pressure 555
Fuel filter pressure sensor Removal 555
Fuel filter pressure sensor Installation 555
Removal and Installation of Engine coolant temperature sensor 555
Engine coolant temperature sensor Removal 555
Engine coolant temperature sensor Installation 556
Inspection of Engine coolant temperature sensor 556
Removal and Installation of CKP sensor 556
CKP sensor Removal 556
CKP sensor Installation 557
Inspection of CKP sensor 557
Removal and Installation of CMP sensor 557
CMP sensor Removal 557
CMP sensor Installation 557
Inspection of CMP sensor 558
Removal and Installation of Oil pressure sensor 558
Oil pressure sensor Removal 558
Oil pressure sensor Installation 558
Inspection of Oil pressure sensor 558
Removal and Installation of Boost sensor 559
Boost sensor Removal 559
Boost sensor Installation 559
Inspection 559
Removal and Installation of IMT sensor 560
IMT sensor Removal 560
IMT sensor Installation 560
Removal and Installation of Exhaust differential pressure sensor 560
Exhaust differential pressure sensor Removal 560
Exhaust differential pressure sensor Installation 561
Inspection 562
Removal and Installation of Exhaust gas temperature sensor 562
Removal of DPD Temperature Sensor 562
DPD temperature sensor Installation 562
Inspection 563
Engine-side Diagnostic Trouble Code List 564
Troubleshooting – engine 567
Engine-side Trouble 567
Diagnostic Trouble Code 0016 Abnormally Correlation Between Crankshaft Position and Camshaft Position 567
Diagnostic trouble code 0045 Turbocharger Boost Pressure Control System Abnormality 568
Diagnostic Trouble Code 0087 Fuel Rail System Pressure Low Pressure Error 569
Diagnostic Trouble Code 0088 Fuel Rail System Pressure High Pressure Error 572
Diagnostic Trouble Code 0091 Fuel Rail Pressure Regulator Control System Low Input 575
Diagnostic Trouble Code 0092 Fuel Rail Pressure Regulator Control System High Input 576
Diagnostic Trouble Code 0093 Fuel System Leak Detection 578
Diagnostic Trouble Code 0102 Mass Air Flow Sensor System Low Input 581
Diagnostic Trouble Code 0103 Mass Air Flow Sensor System High Input 582
Diagnostic Trouble Code 0112 Intake Temperature Sensor System Low Input 583
Diagnostic Trouble Code 0113 Intake Temperature Sensor System High Input 583
Diagnostic Trouble Code 0117 Engine Coolant Temperature Sensor System Low Input 584
Diagnostic Trouble Code 0118 Engine Coolant Temperature Sensor System High Input 585
Diagnostic Trouble Code 0122 Throttle Sensor System Low Input 586
Diagnostic Trouble Code 0123 Throttle Sensor System High Input 587
Diagnostic Trouble Code 0182 Fuel Temperature Sensor System Low Input 588
Diagnostic Trouble Code 0183 Fuel Temperature Sensor System High Input 589
Diagnostic Trouble Code 0192 Fuel Rail Pressure Sensor System Low Input 590
Diagnostic Trouble Code 0193 Fuel Rail Pressure Sensor System High Input 591
Diagnostic Trouble Code 0201 Injector First Cylinder System Error 592
Diagnostic Trouble Code 0202 Injector Second Cylinder System Error 593
Diagnostic Trouble Code 0203 Injector Third Cylinder System Error 594
Diagnostic Trouble Code 0204 Injector Fourth Cylinder System Error 595
Diagnostic Trouble Code 0217 Engine Coolant High Temperature Error 596
Diagnostic Trouble Code 0219 Engine High Rpm Error 597
Diagnostic Trouble Code 0234 Turbocharger High Boost Pressure State 598
Diagnostic Trouble Code 0237 Turbocharger Boost Sensor Circuit Low Input 600
Diagnostic Trouble Code 0238 Turbocharger Boost Sensor Circuit High Input 601
Diagnostic Trouble Code 0299 Turbocharger Low Boost Pressure Abnormality 602
Diagnostic Trouble Code 0335 Crankshaft Position Sensor System Error 604
Diagnostic Trouble Code 0340 Camshaft Position Sensor System Error 605
Diagnostic Trouble Code 0380 Glow Plug System Error 607
Diagnostic Trouble Code 0404 EGR1 Control System Error 608
Diagnostic Trouble Code 0409 EGR1 Position Sensor System Error 609
Diagnostic Trouble Code 0411 Turbocharger Control Module Signal Error 610
Diagnostic Trouble Code 041C IMT Sensor System High Input 611
Diagnostic Trouble Code 041D IMT Sensor System Low Input 612
Diagnostic Trouble Code 0426 Pre-filtered Exhaust Gas High Temperature Error 613
Diagnostic Trouble Code 0427 Exhaust Temperature Sensor 1 System Low Input (pre-filter) 613
Diagnostic Trouble Code 0428 Exhaust Temperature Sensor 1 System High Input (pre-filter) 614
Diagnostic Trouble Code 042B Exhaust Gas High Temperature Error Before Oxidation Catalyst 616
Diagnostic Trouble Code 042C Exhaust Temperature Sensor 2 System Low Input (before oxidation catalyst) 616
Diagnostic Trouble Code 042D Exhaust Temperature Sensor 2 System High Input (before oxidation catalyst) 617
Diagnostic Trouble Code 0522 Oil Pressure Sensor System Low Input 619
Diagnostic Trouble Code 0523 Oil Pressure Sensor System High Input 620
Diagnostic Trouble Code 0560 System Voltage Error (12 V system) 621
Diagnostic Trouble Code 0563 System Voltage High Input 622
Diagnostic Trouble Code 0601 Control Module Memory Checksum Error 623
Diagnostic Trouble Code 0602 Control Module Program Error 623
Diagnostic Trouble Code 0604 Control Module RAM Error 624
Diagnostic Trouble Code 0606 Control Module Processing Device Error 625
Diagnostic Trouble Code 060B Control Module A/D Converter Processing System Characteristics Error 625
Diagnostic Trouble Code 0638 Throttle Actuator Control System Characteristic Error 626
Diagnostic Trouble Code 0641 Sensor Voltage System Error (reference 1) 627
Diagnostic Trouble Code 0651 Sensor Voltage System Error (reference 2) 629
Diagnostic Trouble Code 0685 ECM Main Relay Control System Low Input 630
Diagnostic Trouble Code 0687 ECM Main Relay Control System High Input 631
Diagnostic Trouble Code 0697 Sensor Voltage System Error (reference 3) 631
Diagnostic Trouble Code 1093 Fuel Rail Pressure Low Pressure Error 633
Diagnostic Trouble Code 1112 Boost Temperature Sensor System Low Input 636
Diagnostic Trouble Code 1113 Boost Temperature Sensor System High Input 636
Diagnostic Trouble Code 1261 Injector Group 1 Voltage Control System Error 637
Diagnostic Trouble Code 1262 Injector Group 2 Voltage Control System Error 638
Diagnostic Trouble Code 1293 Fuel Filter Pressure Sensor System Low Input 638
Diagnostic Trouble Code 1294 Fuel Filter Pressure Sensor System High Input 639
Diagnostic Trouble Code 1404 EGR 1 Close Position Characteristic Error 640
Diagnostic Trouble Code 1455 DPD Restriction 2 641
Diagnostic Trouble Code 1471 DPD Regeneration Error 644
Diagnostic Trouble Code 1621 Control Module EEPROM Error 646
Diagnostic Trouble Code 1655 Sensor Voltage System Error (reference 4) 646
Diagnostic Trouble Code 2146 Injector Group 1 Voltage Control System Error 648
Diagnostic Trouble Code 2149 Injector Group 2 Voltage Control System Error 649
Diagnostic Trouble Code 2228 Atmospheric Pressure Sensor System Low Input 651
Diagnostic Trouble Code 2229 Atmospheric Pressure Sensor System High Input 652
Diagnostic Trouble Code 242F DPD Restriction 653
Diagnostic Trouble Code 2452 DPD Differential Pressure Sensor System Error 655
Diagnostic Trouble Code 2453 DPD Differential Pressure Sensor System Characteristic Error 657
Diagnostic Trouble Code 2454 DPD Differential Pressure Sensor System Low Input 659
Diagnostic Trouble Code 2455 DPD Differential Pressure Sensor System High Input 660
Diagnostic Trouble Code 2456 DPD Differential Pressure Sensor Learning Position Error 661
Diagnostic Trouble Code 2458 DPD Regeneration Time Error 662
Diagnostic Trouble Code 2527 Turbocharger Vacuum Sensor System Low Input 664
Diagnostic Trouble Code 2528 Turbocharger Vacuum Sensor System High Input 665
Diagnostic Trouble Code 0001 CAN Bus Error 666
Diagnostic Trouble Code 0073 CAN Bus Error 667
Diagnostic Trouble Code 0101 TCM Communication Error 668
Diagnostic Trouble Code 0110 Turbocharger Control Module Communication Abnormality 669
Data Reference Values 671
Non-operational P rotation 671
Two pump relief 672
J HYDRAULIC EQUIPMENT (PUMP, OPERATION SYSTEM VALVE) 675
Main Equipment Table 680
160X3 680
Hydraulic Device 680
Hydraulic Pump 680
Control-related 680
Control Valve 680
Solenoid Valve (4 stack) 681
Valve for Left/Right Operations 681
Remote Control Valve for Travel Operations 681
Remote Control Valve Characteristic Diagram 682
Operation Remote Control Valve Control Diagram 682
Travel Remote Control Valve Control Diagram 683
Cushion Valve (heat circuit, with shuttle valve) 683
Selector Valve (option) 683
Basic Functions 684
Oil Temperature Gauge 684
Static Horsepower Control 685
Pressure Boost Control 686
Swing Relief Cut 688
Boom Down Energy Save 689
Auto Energy Save 690
Stroke Control 691
Feed Pump Automatic Stop 693
Hydraulic Fluid Filter Clog 694
Solenoid Sticking Prevention 695
Hot Shutdown Warning 696
Breaker Mode 697
Crusher Mode 697
Port Diagram 698
Hydraulic Pump 698
Control Valve 699
Relief Valve 699
4 Stack Solenoid Valve 702
2 Stack Solenoid Valve 703
Remote Control Valves (upper, travel) 704
Remote Control Valves (left-right) 704
Remote Control Valve (travel) 704
Reducing Valve (single) 705
Cushion Valve 705
2-way Selector Valve 706
Direction Valve 706
Shut-off Valve 707
Manifold Under Cab 707
Manifold (accumulator section) 708
Manifold (hydraulic oil tank section) 709
Hydraulic Device 710
Pump P – Q Diagram 710
Main Equipment Structure and Operation Explanation 711
Hydraulic Pump 711
Structure and Operation Explanation 711
Hydraulic Pump Internal Structure Diagram 712
Overall View 712
Drive Shaft Front Side 713
Drive Shaft Rear Side 714
Part Table 715
Regulator 715
Regulator Operation Explanation 715
Regulator Operation Explanation Diagram 719
Front Side Regulator Internal Structure Diagrams 721
Rear Side Regulator Internal Structure Diagram 724
Gear Pump 727
Gear Pump Internal Structure Diagram 727
Structure and Operation Explanation 728
Control Valve 729
Basic configuration 729
Operation 743
4 Stack Solenoid Valve Operation Explanation 768
External Shape Diagram and Component Parts 768
Operation Explanation 769
3 Stack Solenoid Valve 770
Upper Pilot Valve (remote control valve) 771
Structure 771
Function 771
Operation 772
Structural Diagram 775
Travel Pilot Valve (remote control valve) 776
Operation 776
Pressure Reduction Valve Section 777
Operating Section Damping Mechanism Section 777
Structural Diagram 780
Cushion Valve 781
Structure 781
Operation Explanation 782
Pressure Bleeding Operations 786
Removal and Installation of Hydraulic Oil Tank 787
Removal of Hydraulic Oil Tank 787
Installation of Hydraulic Oil Tank 791
Removal and Installation of Hydraulic Pump 792
Removal of Hydraulic Pump 792
Installation of hydraulic pump 795
Removal and Installation of Pump Coupling 796
Removal of Pump Coupling 796
Installation of Pump Coupling 797
Removal and Installation of Control Valve 799
Removal of Control Valve 799
Installation of Control Valve 802
Removal and Installation of Pilot Blocs 803
Removal and Installation of Travel Remote Control Valve 804
Removal of Travel Remote Control Valve 804
Installation of Travel Remote Control Valve 805
Removal and Installation of Operation Remote Control Valve 807
Removal of Operation Remote Control Valve (Left) 807
Installation of Operation Remote Control Valve (Left) 809
Removal of Operation Remote Control Valve (right side) 811
Installation of Operation Remote Control Valve (right side) 813
Removal and Installation of 4 Stack Solenoid 815
Removal of 4 Stack Solenoid Valve 815
Installation of 4 Stack Solenoid Valve 816
Removal and Installation of Cushion Valve 818
Removal of Cushion Valve 818
Installation of Cushion Valve 819
Procedures for Assembly and Disassembly of Hydraulic Pump Main Unit 821
Tools 821
Disassembly Procedure 822
Assembly Procedure 824
Pump Main Unit Maintenance Standards 828
Replacement standards for worn parts 828
Standards for repairing cylinders, valve plates, and swash plates (shoe plates) 828
Tightening torque 829
Overall View 829
Attached diagram 1 pump assembly cross-section diagram 829
Drive Shaft Front Side 830
Drive Shaft Rear Side 831
Part Table 832
Regulator Operation Explanation 833
Regulator adjustment 836
Tables and diagrams 838
Regulator Assembly and Disassembly Procedures 842
Tools 842
Disassembly preparations 843
Disassembly procedures 843
Assembly procedures 845
Diagram 1 Front-side regulator assembly cross-section diagram 848
Diagram 2 Rear-side regulator assembly cross-section diagram 851
Procedures for Assembly and Disassembly of Control Valve 853
Main plunger section 853
Foot relief valve 855
Main relief valve 856
Disassembly 856
Assembly and pressure setting 858
Pressure setting 859
Overload relief valve 860
Center bypass valve 862
Arm regeneration check 863
Boom back pressure check 864
Load hold valve 865
Boom regeneration check 868
Check valve 869
Swing priority valve 871
Check valve (swing priority path) 874
Arm regeneration valve 876
Travel signal switchover spool 877
Procedures for Assembly and Disassembly of Operation Remote Control Valve 878
Maintenance Procedures 878
Required Tools and Tightening Torque 878
Maintenance Standards 879
Disassembly Procedures 880
Assembly Procedures 882
Causes of Trouble and Countermeasures 884
Procedures for Assembly and Disassembly of Travel Remote Control Valve 889
Maintenance Procedures 890
Disassembly Procedures 890
Assembly Procedures 894
Causes of Trouble and Countermeasures and Cross-section Diagram 899
Assembly and Disassembly of Cushion Valve 902
Disassembly Procedures 902
Reverse Operation Spool Section 902
Check Plunger Section with Throttle 902
Shuttle Valve Section 902
Assembly Procedures 903
Reverse Operation Spool Section 903
Check Plunger Section with Throttle 903
Shuttle Valve Section 903
Written Materials 904
Pressure Measurement and Adjustment Procedures 906
Procedures for Pressure Measurement from the Monitor Display 906
Monitor and Switch Panel 906
Pressure Measurement Method 906
Operating Method 906
PROCEDURES FOR MEASURING HYDRAULIC OIL TEMPERATURE FROM THE MONITOR DISPLAY 907
Hydraulic Oil Temperature Measurement Method 907
Operating Method 907
Procedures for Pressure Measurement by Installing Pressure Gauge 908
Preparations 908
Items to prepare 908
Pressure Measuring Port 909
Control Valve 910
Location of Relief Valves 910
Pressure Measurement Preparations 912
Pressure Measurement 913
Main Pressure Measurement 913
A Attachment Pressure Measurement 914
Boom-down pressure measurement 915
D Option Line Pressure Measurement 915
Pilot Pressure Measurement 916
Installation of Pressure Gauge 916
Negative Control Pressure Measurement 916
Installation of Pressure Gauge 916
Pressure Adjustment 916
Main Pressure Adjustment 916
Pressure measurement and adjustment preparation work 917
Main Relief Pressure Adjustment 918
Overload Relief Pressure Adjustment 918
Swing Relief Pressure Adjustment 919
Pilot Pressure Adjustment 920
Hydraulic Pump Flow Measurement Procedures 921
Preparations 921
Items to Prepare 921
Work Preparations 922
Flow Measurement 923
Air Bleed Procedure 925
Hydraulic Pump 925
Check 925
Hydraulic Equipment Layout 926
Overall view 927
Pump Chamber Hydraulic Equipment Layout 928
SWING BODY CENTER SECTION HYDRAULIC EQUIPMENT 929
HOUSING LEFT SIDE HYDRAULIC EQUIPMENT LAYOUT 930
LAYOUT OF HYDRAULIC EQUIPMENT IN CAB 931
J EXPLANATION OF HYDRAULIC CIRCUIT AND OPERATIONS (STANDARD MODEL) 933
J EXPLANATION OF HYDRAULIC CIRCUIT AND OPERATIONS (OPTION) 1015
N CAB 1029
Removal and Installation of Operator’s Seat 1032
Removal of Operator’s Seat 1032
Installation of Operator’s Seat 1032
Removal and Installation of Cab Assembly 1033
Removal of Cab Assembly 1033
Installation of Cab Assembly 1037
Removal and Installation of Wiper 1038
Removal of Wiper 1038
Installation of wiper 1038
Removal and Installation of Cab Front Glass 1039
Removal of Cab Front Glass 1039
Installation of Cab Front Glass 1040
Removal and Installation of Right-side Window Glass 1041
Removal of Right-side Window Glass 1042
Installation of Right-side Window Glass 1043
Removal and Installation of Door (Upper) Sash Glass 1046
Removal of Door (Upper) Sash Glass 1047
Installation of Door (Upper) Sash Glass 1048
Window Lock Adjustment Procedures 1051
Window Lock (front side) 1051
Window Lock (rear side) 1051
Tightening torque 1053
R ELECTRICAL PARTS 1055
Electrical and Engine Functions and Service Support 1060
Service Support 1060
Screen Operations 1060
Screen Display List 1060
CHECK Screen List 1061
MACHINE STATUS 1061
FAULT HISTORY 1065
WORK HISTORY 1066
ENGINE HISTORY 1068
HYDRAULIC HISTORY 1072
PART NUMBER 1074
List of Control Unit Screens 1075
CONTROLLER A 1076
CONTROLLER B 1078
MONITOR 1081
ECM 1083
AIR CONDITIONER 1083
COMMUNICATION 1084
SETUP Screen List 1085
MACHINE SELECT 1085
PARAMETERS 1089
RESET Screen List 1091
Basic Functions 1092
Monitor Display Dimming 1092
Eco Gauge 1093
Diagnostic Trouble Code Indicator 1094
Clock 1094
Accessories 1095
Working Light 1095
Room lamp 1096
Radio Mute 1098
Wiper and Washer 1099
Horn 1100
Back/Side View Monitor 1101
Precautions When Installing the Camera 1101
Anti-theft 1102
Enabling the anti-theft function 1102
Password 1102
Immobilizer Key 1103
Battery Disconnect Switch 1104
Reset 1105
Half Reset/All Reset 1105
Milli-amp List 1106
Safety 1108
Lever Lock 1108
Alternator Power Generation Detection 1109
Setting 1111
Model Selection 1111
Throttle Volume Default Setting Value 1116
Password Setting 1116
Clock Adjustment 1117
Parameter Settings 1118
Option Flow Setting 1120
Screen Brightness Setting 1121
Service Monitor 1123
How to get into “Service Screen” 1123
General Operation on Service Monitor 1123
Engine Service Monitor 1124
Service Monitor Structure 1124
ENGINE INFORMATION 1125
Data Confirmation 1125
Data Transfer (Copy) 1125
QR (INJECTOR) CODE 1127
Injector Number 1127
Screen Layout 1127
Data Source Selection 1128
Manual Input 1128
DEVICE TEST 1129
Common Rail Pressure Test 1129
Injector Balance Test 1130
Injector Forced Drive Test 1131
ECM Memory Clear 1131
DPD Slow Regeneration 1132
DPD Manual Regeneration 1133
DPD Automatic Regeneration 1134
EGR Valve Control Test (if equipped) 1134
VG Turbo Control Test 1135
Intake Throttle Control Test 1135
Turbo Boost Test 1136
Computer Explanation 1137
Connection Connector Pin Layout 1143
Computer A 1143
Computer B 1144
Monitor 1145
Sequence Circuit Diagram 1146
Code table 1146
Overall 1149
Block diagram 1151
Computer A 1151
Computer B 1152
ECM 1153
Monitor 1154
Air Conditioner 1155
Lever Lock 1156
Horn 1156
Working lights 1156
Option 1157
Other 1158
Electrical Symbol List 1159
Electrical Equipment Layout Diagram 1160
Main Unit Left Side Layout Diagram (radiator chamber) 1160
Engine Section Layout Diagram 1162
Main Unit Right Side Layout Diagram (pump chamber) 1165
Main Unit Center Section Layout Diagram 1166
Cab Layout Diagram 1 1167
Cab Layout Diagram 2 1169
Layout Around Operator Seat 1171
Stand Alone Parts Diagram 1172
Removal and Installation of Wiper Controller 1191
Removal of Wiper Controller 1191
Installation of wiper controller 1191
Removal and Installation of Wiper Motor 1192
Removal of Wiper Motor 1192
Installation of wiper motor 1193
Removal and Installation of Monitor 1194
Removal of Monitor 1194
Installation of Monitor 1195
ECM Replacement Procedure 1196
Removal and Installation of ECM 1197
Removal of ECM 1197
Installation of ECM 1197
Removal and Installation of Computer A 1198
Removal of Computer A 1198
Installation of Computer A 1198
Removal and Installation of Computer B 1199
Removal of Computer B 1199
Installation of Computer B 1199
Air Conditioner Overall Diagram 1200
Frame 1200
Cab 1202
Equipment Layout Diagram 1205
Circuit Diagram 1207
Air Conditioner Circuit Diagram 1207
Explanation of Functions 1209
Explanation of Control 1209
Air Mix Motor Actuator Control 1210
Blow Mode Motor Actuator Control 1210
Refresh/Recirculate Switch Motor Actuator Control 1211
Blower Amp Control 1212
Compressor Clutch Control 1214
COOLMAX Control and HOTMAX Control 1215
Abnormality Detection and Control after Abnormality Detected 1215
Monitor Mode 1219
Door Switch Control 1220
Inside Air Filter Clogging Detection Control 1221
Actuator Inspection 1224
Air Mix Motor Actuator Inspection 1224
Refresh/Recirculate Switch Motor Actuator Inspection 1225
Mode Motor Actuator Inspection 1226
Self-diagnosis Function with Panel Display 1227
Abnormality Display and Self-check Procedures 1227
Abnormality Display Position 1227
Explanation of Abnormality Display 1227
Motor Actuator Abnormality 1227
Sensor Abnormality 1228
Explanation of Monitor Mode 1228
Monitor Mode Display Position 1228
Monitor Mode Display Operating Method 1229
Display Contents in Monitor Mode 1230
Air Conditioner Troubleshooting 1231
Part Function and Good/Poor Judgment 1236
Control Panel 1236
Blower Amp 1236
Relay 1237
Air Mix Actuator 1238
Refresh/Recirculate Actuator 1239
Blow Mode Actuator 1239
Evaporator Sensor 1240
Dual Pressure Switch 1240
Solar Radiation Sensor 1241
Inside Air Sensor 1242
Assembly and Disassembly of Unit 1243
Removal of Blower Unit 1243
Replacement of Blower Motor 1243
Replacement of Blower Amp 1243
Removal of Heater Core 1244
Removal of Heat Case Right/Left 1244
Replacement of Evaporator and Expansion Valve 1244
Installation of Evaporator Sensor 1245
Replacement of Motor Actuator 1245
Removal and Installation of Compressor 1246
Removal of Compressor 1246
Installation of Compressor 1246
Removal and Installation of Condenser 1247
Removal of Condenser 1247
Installation of Condenser 1248
Removal and Installation of Receiver Dryer 1249
Removal of Receiver Dryer 1249
Installation of Receiver Dryer 1250
Work Precautions 1251
Work Procedures 1252
Air Conditioner Refrigerant Filling is Divided into the “Vacuum Operation” and “Gas Filling Operation” 1252
Operation Chart 1252
Tools 1253
Filling Procedures 1254
Charging Hose Connection Positions 1254
Gauge Manifold Connection 1254
Vacuuming 1256
Gas Filling Operation, High-pressure Side 1257
Gas Filling Operation, Low-pressure Side 1258
R ELECTRICAL CONNECTOR WIRING DIAGRAM 1261
R ELECTRICAL PARTS AND WIRING ASSEMBLY DIAGRAM 1271
V ATTACHMENTS 1283
Main Equipment Table 1286
160X3 1286
Backhoe Attachment 1286
Cylinder 1286
Maintenance Standards 1287
Attachment (backhoe) 1287
1 Boom and Swing Frame Installation Section 1288
2 Boom Cylinder and Swing Frame Installation Section 1289
3 Boom and Boom Cylinder Installation Section 1290
4 Boom and Arm Cylinder Installation Section 1291
5 Boom and Arm Installation Section 1292
6 Arm and Arm Cylinder Installation Section 1293
7 Arm and Bucket Cylinder Installation Section 1294
8 Arm and Arm Link Installation Section 1295
9 Bucket and Bucket Link Installation Section 1296
10 Bucket Link and Bucket Cylinder Installation Section 1297
11 Bucket and Arm Installation Section 1298
Removal and Installation of Bucket Cylinder 1299
Removal of Bucket Cylinder 1299
Installation of Bucket Cylinder 1301
Removal and Installation of Arm Cylinder 1302
Removal of Arm Cylinder 1302
Installation of Arm Cylinder 1304
Removal and Installation of Boom Cylinder 1307
Removal of Boom Cylinder 1307
Installation of Boom Cylinder 1309
Procedures for Operation/Assembly and Disassembly of Hydraulic Cylinder (made by KYB) 1312
Specifications and Structure Diagram (including the assembly diagram and parts table) 1312
Basic functions 1312
Function of Each Location 1312
Cylinder Head Assembly 1312
Piston Assembly 1313
Pipe Assembly 1315
Handling Precautions 1315
Precautions for Installing the Cylinder on the Machine Body 1315
Usage Cautions 1316
Maintenance and Inspection Cautions 1316
Maintenance Inspection and Service 1318
Trouble Diagnostics 1319
Storage Standards 1323
Storing Parts Individually (In principle, store indoors ) 1323
When Mounted on Vehicle Body 1324
Recommended Anti-rust Oil 1324
Assembly and Disassembly Procedures 1324
Preparations ····· Prepare the Following before Starting Disassembly 1324
General Work Precautions 1324
Maintenance Standards 1324
Inspection after Assembly 1325
Required Tool 1326
General Tool 1326
Special Jig 1327
Special Jigs Part Number List 1328
Disassembly Procedures 1329
Drain the Oil 1329
Secure the Cylinder 1329
Removal of Cylinder Head 1329
Pull out the Piston Rod 1329
Fasten the Piston Rod 1330
Remove the Piston Nut 1330
Removal of Piston etc 1330
Disassembly of the Retraction Side Cushion Ring 1331
Remove the Piston Seal 1331
Disassembly of the Buffer Ring 1331
Disassembly of U-ring and Wiper Ring 1331
Removal of O-ring and Backup Ring 1331
Disassembly of Bushing 1331
Removal of Pin Bushing 1332
Cleaning and Storage 1332
Assembly Procedures 1333
Installation of Pin Bushing 1333
Replacement of Seals 1333
Assembly of Cylinder Head Assembly 1333
Assembly of Piston Assembly 1334
Assembly of Piston Rod Assembly 1334
Insertion of Piston Rod into the Tube 1336
Cylinder Head Tightening 1336
Installation of Line 1336
Test Operation 1337
Usage Limits 1338
Structural Diagram 1339
Boom Cylinder 1339
Arm Cylinder 1342
Bucket Cylinder 1345
Port Diagram 1348
HBCV 1348
Removal and Installation of HBCV 1349
Removal and Installation of Arm HBCV 1349
Removal of arm HBCV 1349
Installation of arm HBCV 1349
Removal and Installation of Boom HBCV 1350
Removal of Boom HBCV 1350
Installation of boom HBCV 1351
Air Bleed Procedure 1352
HBCV 1352
Boom Cylinder HBCV 1352
Arm Cylinder HBCV 1353
Removal and Installation of Bucket 1354
Removal of Bucket 1354
Installation of Bucket 1354
Removal and Installation of Bucket Link 1356
Removal of Bucket Link 1356
Installation of Bucket Link 1356
Removal and Installation of Arm 1358
Removal of Arm 1358
Installation of Arm 1359
Removal and Installation of Boom 1360
Removal of Boom 1360
Installation of Boom 1363
Z OTHER 1367
Specifications 1371
160X3 1371
ENGINE 1371
HYDRAULIC SYSTEM 1371
HYDRAULIC CONTROLS 1372
ELECTRICAL SYSTEM 1372
OPERATOR ENVIRONMENT 1373
UNDERCARRIAGE 1373
MASS 1374
DIGGING FORCE (with 0 62 m3 Sumitomo Bucket) (ISO 6015) 1374
DIMENSIONS 1374
WORKING RANGES 1374
SYSTEM FLUID CAPACITIES AND SPECIFICATIONS 1375
Arm Dimension 1376
160X3 1376
Standard Arm [2 62 m (8 5958 ft )] 1376
Long Arm [3 05 m (10 0066 ft )] 1378
Main Unit Weight 1380
160X3 1380
Divided Weight (standard specifications) 1380
Stand Alone Part Weight 1381
Shoe Weight (per side) 1381
Arm Weight 1381
Bolt Size and Torque Table 1382
Special Torque Settings 1382
Overall View 1386
160X3 1386
Standard Arm [2 62 m (8 5958 ft)] 1386
Long Arm [3 05 m (10 0066 ft)] 1387
WORK RANGE DIAGRAM 1388
160X3 1388
Standard Arm [2 62 m (8 5958 ft)] 1388
Long Arm [3 05 m (10 0066 ft)] 1390
New Machine Performance Judgment Table 1392
Table of Standards 1392
Measurement Method 1394
Engine Speed 1394
Pressure in Each Section 1394
Cylinder Falling Amount 1394
Attachment Speed 1394
Swing Speed 1395
Swing (180°) Brake Angle 1395
Travel Speed 1396
Travel Deviation 1396
Travel Sprocket Speed 1397
Shoe Tension Amount 1397
Swing Ball Race Bearing Movement Amount and Bucket Tip Movement Amount 1398
FLUIDS AND LUBRICANTS 1400
HYDRAULIC FLUID 1400
Engine Oil 1400
Oil Grade 1400
FUEL 1401
Conditions applicable to diesel fuel 1401
Recommended Conditions That Can Be Applied To Diesel Fuel 1401
Main Unit-side Diagnostic Trouble Code List 1402
Main Unit-side Trouble 1404
Diagnostic Trouble Code: 7000 P1 Pressure Sensor Signal Abnormality 1404
Diagnostic Trouble Code: 7001 P2 Pressure Sensor Signal Abnormality 1406
Diagnostic Trouble Code: 7002 N1 Pressure Sensor Signal Abnormality 1408
Diagnostic Trouble Code: 7003 N2 Pressure Sensor Signal Abnormality 1410
Diagnostic Trouble Code: 7020 Upper Pressure Sensor Signal Abnormality 1412
Diagnostic Trouble Code: 7021 Swing Pressure Sensor Signal Abnormality 1414
Diagnostic Trouble Code: 7022 Travel Pressure Sensor Signal Abnormality 1416
Diagnostic Trouble Code: 7023 Arm-in Pressure Sensor Signal Abnormality 1418
Diagnostic Trouble Code: 7040 Fuel Level Sensor Signal Abnormality 1420
Diagnostic Trouble Code: 7041 Oil Temperature Sensor Signal Abnormality 1422
Diagnostic Trouble Code: 7063 Return Filter Clog Switch Abnormality 1424
(Breaker specifications) 1424
(Other than breaker specifications) 1425
Diagnostic Trouble Code: 7065 Boom-up Pilot Pressure Sensor Signal Abnormality 1426
Diagnostic Trouble Code: 7067 Bucket-close Pilot Pressure Sensor Signal Abnormality 1428
Diagnostic Trouble Code: 7200 Swing Brake Solenoid Signal Abnormality 1430
Diagnostic Trouble Code: 7201 Travel High-speed Solenoid Signal Abnormality 1432
Diagnostic Trouble Code: 7202 Pressure Boost Solenoid Signal Abnormality 1434
Diagnostic Trouble Code: 7203 Travel Alarm Buzzer Signal Abnormality 1437
Diagnostic Trouble Code: 7204 Power Save Solenoid Signal Abnormality 1439
Diagnostic Trouble Code: 7206 Option Line Switchover Solenoid Signal Abnormality 1442
Diagnostic Trouble Code: 7207 Free Swing Solenoid Signal Abnormality 1444
Diagnostic Trouble Code: 7212 Shut-off Solenoid Signal Abnormality 1446
Diagnostic Trouble Code: 7240 Pump Horsepower Proportional Valve Signal Abnormality 1448
Diagnostic Trouble Code: 7241 P1 Flow Control Proportional Valve Signal Abnormality 1450
Diagnostic Trouble Code: 7246 2 Pumps Flow Solenoid Signal Abnormality 1452
Diagnostic Trouble Code: 7247 Boom-down Proportional Valve Signal Abnormality 1454
Diagnostic Trouble Code: 7253 DPD Regeneration Request Output Signal Abnormality 1456
Diagnostic Trouble Code: 7254 Washer Output Abnormality 1458
Diagnostic Trouble Code: 7400 Abnormally High Coolant Temperature [(105°C (221 0°F) or higher)] 1460
Diagnostic Trouble Code: 7401 Abnormally High Coolant Temperature [ 110 °C ( 230 0 °F )or higher ] 1461
Diagnostic Trouble Code: 7404 Abnormally High Oil Temperature [98 °C (208 4 °F) or higher] 1462
Diagnostic Trouble Code: 7405 Abnormally High Boost Temperature [ 80 °C ( 176 0 °F )or higher ], 7406 Abnormally High Boost Temperature [ 90 °C ( 194 0 °F )or higher ] 1463
Diagnostic Trouble Code: 7420 Abnormally Low Alternator Voltage 1464
Diagnostic Trouble Code: 7421 Coolant Level Reduction 1466
Diagnostic Trouble Code: 7422 Abnormally Low Engine Oil Pressure 1467
Diagnostic Trouble Code: 7423 Air Cleaner Clogging 1468
Diagnostic Trouble Code: 7424 Return Filter Clogging (with breaker) 1469
Diagnostic Trouble Code: 7426 Fuel Filter Clogging 1 1470
Diagnostic Trouble Code: 7427 Fuel Filter Clogging 2 1471
Diagnostic Trouble Code: 7601 Monitor Communication Abnormality 1472
Diagnostic Trouble Code: 7602 ECM Communication Abnormality 1473
Diagnostic Trouble Code: 7605 ECM Mismatch 1474
Diagnostic Trouble Code: 7606 EEPROM Data Abnormality 1475
Diagnostic Trouble Code: 7607 Computer C Communication Abnormality 1476
Diagnostic Trouble Code: 7608 Camera Abnormality 1477
Diagnostic Trouble Code: 7609 EEPROM (B) Data Abnormality 1479
Diagnostic Trouble Code: 7610 EEPROM (C) Data Abnormality 1480
Diagnostic Trouble Code: 7611 Computer A Communication Abnormality 1481
Diagnostic Trouble Code: 7612 Air Conditioner Communication Abnormality 1482
Diagnostic Trouble Code: 7613 Monitor Communication CAN Abnormality 1483
Diagnostic Trouble Code: 7614 Air Conditioner Panel Mismatch 1484
List of special tools 1485
A 1485
Travel Motor Special Tool 1485
160X3 1485
Take-up Roller Special Tool 1488
160X3 1488
Upper Roller Special Tool 1489
160X3 1489
Lower Roller Special Tool 1490
160X3 1490
Grease Cylinder Special Tool 1491
160X3 1491
Center Joint Special Tool 1491
160X3 1491
C 1492
Swing Motor Special Tool 1492
160X3 1492
H 1493
Engine Oil Filter Special Tool 1493
160X3 1493
Fuel Filter Special Tool 1493
160X3 1493
Injector Special Tool 1493
160X3 1493
Circuit Test Special Tool 1494
160X3 1494
Valve Guide Special Tool 1494
160X3 1494
Cylinder Head Special Tool 1495
160X3 1495
Head Bolt Special Tool 1496
160X3 1496
Crankshaft Special Tool 1496
160X3 1496
Valve Spring Special Tool 1498
160X3 1498
J 1499
Remote Control Valve Special Tool 1499
160X3 1499
R 1501
Gas Filling Special Tool 1501
160X3 1501
PLEASE NOTE:
- This is the same manual used by the DEALERSHIPS to SERVICE your vehicle.
- The manual can be all yours – Once payment is complete, you will be taken to the download page from where you can download the manual. All in 2-5 minutes time!!
- Need any other service / repair / parts manual, please feel free to contact us at heydownloadss @gmail.com . We may surprise you with a nice offer
S.V