John Deere H413 Harvester Head Operator’s Manual F678990 – PDF DOWNLOAD
FILE DETAILS:
John Deere H413 Harvester Head Operator’s Manual F678990 – PDF DOWNLOAD
P/N: F678990_81
Language: English
Division: Forestry
Product Lines: Harvesting Heads
Publication Type: Operator’s Manuals
Associated Models: H413
Series: HARVESTING HEADS SERIES
Serial: EJH413X000006-
Operator’s Manual for Harvesting Heads (Forestry Division)
IMAGES PREVIEW OF THE MANUAL:
TABLE OF CONTENTS:
John Deere H413 Harvester Head Operator’s Manual F678990 – PDF DOWNLOAD
Table of Contents 2
1 Foreword 7
1 1 Copyright 7
1 2 Foreword 7
1 3 Declaration of Incorporation 7
1 4 General assembly instructions 8
1 5 Product identification 8
1 6 Base machine requirements 9
1 7 Standard warranty 9
2 Safety 10
2 1 Follow Laws and Regulations 10
2 1 1 Recognize Safety Information 10
2 1 2 Understand Signal Words 11
2 1 3 Prepare for Emergencies 11
2 1 4 Wear Protective Clothing 12
2 1 5 Handle Chemical Products Safely 12
2 1 6 Cabin protective structures 13
2 2 Operating the harvester head 14
2 2 1 Attach Do not Operate Tag 14
2 2 2 Pay Attention to Bystanders 15
2 2 3 Operate the Boom Safely 15
2 2 4 Keep Danger Zone Clear 16
2 2 5 Avoid saw chain shots 16
2 2 6 Avoid Crush Points 17
2 2 7 Avoid Power Lines 18
2 2 8 What To Do If the Machine Catches Fire? 18
2 2 9 After a fire 19
2 3 Maintenance 19
2 3 1 Keep Machine in Good Condition 20
2 3 2 Use Proper Clothing 20
2 3 3 Use Proper Tools 21
2 3 4 Support Machine Properly 21
2 3 5 Avoid High Pressure Fluids 22
2 3 6 Avoid Heating near Pressurized Fluid Lines 22
2 3 7 Make Welding Repairs Safely 23
2 3 8 Dispose of Waste Properly 23
2 4 Safety Decal Locations 24
3 Specifications 25
3 1 Harvester head brochure 25
3 2 Harvester head specifications 25
3 3 General hydraulic system requirements 26
3 4 General hose and fitting requirements 26
3 5 Key characteristics 27
3 6 Harvester head components (H413) 28
4 Transportation and storage 29
4 1 Preparing for storage 29
4 2 Transport by road 29
5 Harvesting instructions 30
5 1 Planning the work 30
5 1 1 Example of map sketch 30
5 2 Thinning 30
5 2 1 Thinning with harvester alone 31
5 2 2 Thinning with harvester and chain saw 32
5 2 3 Thinning between logging roads 32
5 3 Regeneration harvesting 33
5 3 1 Felling into trees 33
5 3 2 Felling outwards from the stand 34
5 3 3 Felling in both directions 34
5 4 Felling 35
5 4 1 Felling stage 35
5 4 2 Felling on slope 36
5 4 3 Felling trees with large roots 36
5 5 Delimbing and crosscutting 37
6 Systems and Components 38
6 1 Delimbing knives 38
6 1 1 Delimbing quality 38
6 1 2 Advantages of sharp knives 39
6 1 3 Delimbing knives cylinders 39
6 2 Four roller feeding 40
6 2 1 Feed rollers 41
6 2 2 Inner roller alternatives 42
6 2 3 Outer roller alternatives 43
6 2 4 Grabbing 44
6 3 Saw unit 45
6 3 1 Saw feeding mechanism 46
6 3 2 Saw chains and saw bars (SuperCut 100S) 47
6 3 3 Saw chains and saw bars 47
6 3 4 Chain lubrication system 48
6 3 4 1 Saw unit lubrication pump 49
6 3 4 1 1 Alternative capacities 50
6 3 4 2 Stroke pump alternatives 50
6 3 4 3 Chain oil tank 51
6 3 5 Chain grease lubrication system 52
6 3 5 1 Grease pump functions 53
6 3 5 2 Grease pump components 54
6 3 5 3 Meter valves 55
6 3 6 Chain shot guard 56
6 3 7 Saw sensor 57
6 4 Sensors 58
6 5 Length measuring device 59
6 5 1 Length measuring device (H413 and H415) 60
6 5 2 Measuring wheel alternatives 61
6 5 3 Length measuring sensor 62
6 6 Diameter measuring device, upper knives 63
6 7 PEvo harvester head valve 64
6 7 1 Hydraulic functions 65
6 7 2 PEvo connectors 66
6 7 3 XA connector 67
6 7 4 HHC (L22) connectors (H413/H415) 68
6 8 Hydraulic hoses 69
6 9 Optional equipment 69
6 9 1 Multi-tree handling (MTH) 70
6 9 1 1 Multi-Tree Handling (MTH) 71
6 9 1 2 MTH – Tall components 72
6 9 2 Color marking unit 73
6 9 2 1 Nozzles in saw box 74
6 9 2 2 Nozzles in lower knife 75
6 9 3 Stump treatment 76
6 9 3 1 Stump treatment spray 77
6 10 Tutorial videos for main harvester head components 78
7 Maintenance 79
7 1 General 79
7 1 1 Preparations 80
7 1 2 Welding instructions 80
7 1 3 Special tools 81
7 1 3 1 Extractor tool for Deutsch™ connectors 82
7 1 3 2 Saw motor puller tool 83
7 1 3 3 Saw motor installation tool 84
7 1 3 4 Assembly tool for feed cylinder piston gasket 85
7 1 3 5 Chain tensioning check valve installation tool 86
7 1 3 6 Hook spanners 86
7 1 3 7 Length measuring wheel bearing puller 87
7 1 3 8 Check valve installation tool 87
7 1 3 9 Pressure relief valve installation tool 88
7 1 3 10 Sharpening gauge 88
7 1 4 H413 tightening torques 89
7 1 5 Conical sleeve pin tightening 89
7 1 6 Fluids and lubricants 90
7 1 7 Hydraulic pressure measurements 92
7 1 7 1 Main relief valve pressure 93
7 1 7 2 Low pressure 94
7 1 7 3 Pilot pressure 95
7 1 7 4 Saw chain tensioning pressure 96
7 1 7 5 Length measuring pressure 97
7 1 7 6 Color marking pump pressure 98
7 1 7 7 MAF pressure 99
7 1 8 Tutorial video for harvester head daily maintenance 100
7 2 Service intervals 100
7 3 Every 10 hours or daily 101
7 3 1 Check 102
7 3 1 1 Check diameter measuring device 103
7 3 1 2 Check chain lubrication system 104
7 3 1 3 Check multi-tree handling device 105
7 3 2 Fill chain oil tank 106
7 3 3 Fill grease lubrication container 107
7 3 4 Grease 108
7 3 4 1 Grease rotator and link 109
7 3 4 2 Grease length measuring device 110
7 3 4 3 Grease tilt and cylinders 111
7 3 4 4 Grease upper knives and cylinders 111
7 3 4 5 Grease feed roller arms and cylinders 112
7 3 4 6 Grease lower knives and cylinders 112
7 3 4 7 Grease saw unit 113
7 3 4 8 Grease multi-tree handling device 114
7 3 5 Maintain color marking unit 115
7 4 Every 50 hours 115
7 4 1 Check rotator screws 116
7 4 2 Grease the bar holder (SuperCut 100S) 117
7 5 Every 500 hours 117
7 5 1 Grease upper knife shaft housing 118
7 5 2 Grease diameter sensor housing 118
7 5 3 Grease length measuring sensor housing 119
7 5 4 Check 119
7 6 Every 1000 hours 119
7 6 1 Check visually the frame 120
7 6 2 Clean saw chain oil strainer 120
7 6 3 Clean rotator magnetic plug 121
7 6 4 Clean color marking tank strainer 122
7 6 5 Measure hydraulic pressures 122
7 6 6 Sharpen delimbing knives 123
7 6 6 1 Knife sharpening 124
7 6 6 2 Back bevel 125
7 6 7 Tighten rotator screws 126
7 7 As required 127
7 7 1 Saw unit maintenance 127
7 7 1 1 Saw chain components 128
7 7 1 1 1 Changing the Saw Chain (SuperCut 100S) 129
7 7 1 1 2 Changing the Saw Chain 130
7 7 1 1 3 Sharpening the saw chain 130
7 7 1 1 3 1 Using a grinder for sharpening 131
7 7 1 1 3 2 Using a round-file for sharpening 132
7 7 1 1 3 3 Depth gauges 133
7 7 1 1 4 Repairing the saw chain 134
7 7 1 1 4 1 Installing new chain parts 135
7 7 1 2 Chain tensioning 135
7 7 1 2 1 Bleed chain tensioning system (SuperCut 100S) 136
7 7 1 2 2 Bleed chain tensioning system (SC100) 137
7 7 1 3 Remove saw tensioning device (SC100) 138
7 7 1 4 Saw bar 138
7 7 1 4 1 Basic inspection 139
7 7 1 4 2 Changing the saw bar (SuperCut 100S) 140
7 7 1 4 3 Changing the saw bar (SC100) 141
7 7 1 4 4 Changing the Bar Holder (SuperCut 100S) 142
7 7 1 4 5 Changing the Bar Holder (SC100) 143
7 7 1 4 6 Straightening the saw bar 143
7 7 1 4 6 1 Bent bars 144
7 7 1 4 6 2 Twisted bars 145
7 7 1 5 Replacing saw sensor 146
7 7 1 6 Adjusting saw sensor wheel 147
7 7 1 7 Replacing drive sprocket 148
7 7 1 8 Replacing tip sprocket 149
7 7 1 9 Removing saw motor 150
7 7 1 10 Replacing chain shot guard 151
7 7 2 Inspect chain shot guard 152
7 7 2 1 Identification of excessive wear and damage 153
7 7 3 Color marking maintenance 153
7 7 3 1 Check and clean the nozzles 154
7 7 3 2 Check the color supply 155
7 7 3 3 Check the pump 156
7 7 3 4 Bleed color marking unit 157
7 7 3 5 Change the color of the color marking unit 158
7 7 4 Grease lubrication maintenance 158
7 7 4 1 Bleed grease lubrication pump 159
7 7 4 2 Change lubrication volume 160
7 7 5 Replace length sensor 161
7 7 6 Adjust diameter sensor 164
7 7 7 Stump treatment system maintenance 165
Index 166
Attachments 169
Declaration of Incorporation template_harvester_head_en 170
JD_Harvesterheads_400series_EN 175
S.V 04/24