FENDT VarioGuide Katana VarioGuide Novatel VarioGuide Trimble OPERATOR’S MANUAL – PDF DOWNLOAD
DESCRIPTION:
FENDT VarioGuide Katana VarioGuide Novatel VarioGuide Trimble OPERATOR’S MANUAL – PDF DOWNLOAD
Dear Customer
Please note the following:
- Before using the machine, carefully read through the operator’s manual and familiarise yourself with all operating controls and their functions before you begin work. This also applies to the operator’s manual for implements.
- Observe all the operating and maintenance instructions. If you do so, your machine will give you many years of cost-effective and fault-free operation. You will find an overview of all maintenance operations in the maintenance schedule in this maintenance manual.
- Maintenance and repair work should only be carried out at your service workshop.
2.1 Safety and accident prevention regulations
2.1.1 Marking of places that affect your safety
Make sure that any other users have read all the safety instructions as well. The various levels of safety instructions can be distinguished as follows:
DANGER: This symbol, together with the word DANGER, means there is an immediate risk
of danger that must be prevented to avoid the risk of DEATH OR SEVERE INJURY.
WARNING: This symbol, together with the word WARNING, means a potential risk of
danger that must be prevented to avoid the risk of DEATH OR SEVERE INJURY.
CAUTION: This symbol, together with the word CAUTION, means there is a potential
danger that must be prevented to avoid the risk of MINOR INJURY.
- The operator’s manual is an integral part of the vehicle package and must be passed on to any subsequent owner in the event of resale. The attention of the new owner should be drawn to this information.
- If the Operator’s Manual is lost or damaged and you need a new one, please contact your FENDT dealer, from whom you will be able to purchase a replacement.
TABLE OF CONTENTS:
FENDT VarioGuide Katana VarioGuide Novatel VarioGuide Trimble OPERATOR’S MANUAL – PDF DOWNLOAD
1 Introduction 13
11 Installation of VarioGuide system 15
2 Safety instructions 17
21 Safety and accident prevention regulations 19
211 Marking of places that affect your safety 19
212 Advice for the operator 19
213 Safe operating environment 20
214 Switching off in an emergency situation 20
3 Row sensor 21
31 Menu overview 23
311 Overview of Row Sensor menu 23
32 Settings 24
321 Row sensor selection 24
322 Row sensor main page 26
323 Row sensor mirroring offset mode selection 26
4 VarioGuide 27
41 Definitions 29
411 GNSS and correction signal 29
412 Satellite reception 29
413 Signal interruption 31
414 Static and dynamic accuracy (satellite drift) 31
415 Convergence time 31
416 Novatel bar indicator, Trimble 31
417 Steering status 32
418 Conditions of use and application possibilities 32
419 Restrictions 33
4110 Switch-off 33
42 Menu overview 34
421 Menu overviewVarioGuide 34
5 Map 39
51 Overviews 41
511 Menu overview: Map settings and information 41
Table of contents
VarioGuide Katana
653020070012
512 Map settings and information 43
513 Menu overview: “Record” map mode 46
514 “Record” map mode 47
515 Menu overview: “Driving” map mode 48
516 “Driving” map mode 48
517 Map view – additional displays 49
52 Mark the tramline working width 51
521 Mark the tramline working width manually 51
522 Automatically mark the tramline working width in a different color 52
523 Automatically mark the tramline working width in a different color: Example 53
53 Markers 54
531 Set markers 54
532 Marker management: Rename or delete marker 55
54 Area marker 56
541 Marking worked area 56
6 Quick Start 57
61 Quick Start Guide 59
611 Quick Start: Overview 59
612 VarioGuide Info 59
613 VarioGuide main menu 60
614 Switch on automatic way line guidance 61
7 Calibration, adjustments, settings and tests 63
71 Calibration 65
711 Gyro system calibration 65
72 Calibrations 68
721 Calibration of steering angle sensor 68
722 Adjust steering valve 71
73 Settings and tests 74
731 System – check system info/system status 74
732 Steering Settings 75
733 SettingVarioGuide offset 76
734 GPS drift compensation 78
735 Manual way-line offset 79
736 Auto Offset 79
8 Components 81
81 System components/controls 83
811 Components for NovAtel or Trimble receiver 83
Table of contents
VarioGuide Katana
653020070012
9 Implement 85
91 Implement selection 87
911 Implement selection 87
912 Add front implement 88
913 Add rear implement 90
92 Implement Settings 93
921 Settings for front implement 93
922 Settings for the rear implement 94
10 Correction signals 97
101 General 99
1011 Overview of correction signals depending on the receiver 99
1012 Available correction signals: NovAtel receiver 99
1013 NovAtel: TerraStar frequencies and coverage 100
1014 Available correction signals: Trimble receiver 101
1015 Trimble: RTX frequencies and coverage 102
1016 Trimble: RTX frequencies 102
1017 VarioGuide Correction signal: connection status messages 103
102 Select the correction signal 105
1021 Select the correction signal 105
103 NovAtel: Submeter accuracy 106
1031 Autonomous NovAtel 106
1032 NovAtel SBAS (EGNOS/WAAS etc) 107
1033 NovAtel TerraStar-L 108
104 NovAtel: Decimeter accuracy 109
1041 NovAtel TerraStar-C 109
105 NovAtel: Centimeter accuracy 110
1051 NovAtel RTK base station 110
10511 RTK base station: NovAtel: Configure internal Satel EASyProof
wireless modem 110
10512 RTK base station: NovAtel receiver: Configure external radio modem
111
1052 NovAtel RTK network 111
10521 RTK network: NovAtel receiver: Configure internal mobile radio
modem 111
10522 RTK network: NovAtel: Configure external mobile radio modem 112
1053 NovAtel RTK Assist (optional) 113
10531 NovAtel RTK ASSIST technology 113
10532 Switch on and configure NovAtel RTK ASSIST 113
106 Trimble: Submeter accuracy 116
Table of contents
VarioGuide Katana
653020070012
1061 Autonomous Trimble 116
1062 Trimble SBAS (EGNOS/WAAS etc) 117
1063 Trimble RangePoint RTX 118
107 Trimble: Decimeter accuracy 119
1071 Trimble CenterPoint RTX Standard 119
108 Trimble: Centimeter accuracy 120
1081 Trimble CenterPoint RTX Fast 120
1082 Trimble RTK base station 120
10821 RTK base station: Trimble: Configure internal Trimble AG-715
403-470 MHz wireless modem 120
10822 RTK base station: Trimble: Configure internal Satel EASyProof
wireless modem 121
10823 RTK base station: Trimble: Configure internal Trimble 900 MHz
wireless modem 122
10824 RTK base station: Trimble: Configure external wireless modem 123
10825 Trimble secure RTK 124
1083 Trimble RTK network 127
10831 RTK network: Trimble: Configure internal mobile radio modem 127
10832 RTK network: Trimble: Configure external mobile radio modem 128
1084 Trimble xFill 129
10841 Trimble xFill technology 129
10842 Switch on and configure Trimble xFill 131
10843 Switch on and configure Trimble xFill Premium (optional) 133
109 RTK network selection and connection status 137
1091 Insert SIM card (mini SIM) 137
1092 RTK network: connection settings for correction signal 138
1093 Connection settings for mobile radio 139
1094 Ntrip settings 142
1095 Roaming 142
1010 Additional adjustments for 144
10101 Manage base stations 144
10102 Fallback 145
11 Field Settings 147
111 Main menu 149
1111 Field Settings 149
1112 Select field 151
1113 Add field 153
1114 Field assistant 154
1115 Display information coordinates 155
1116 Management – fields, waylines and obstacles 156
Table of contents
VarioGuide Katana
653020070012
112 Field boundary 158
1121 Add field boundary 158
1122 Field boundary – record 159
113 Waylines 163
1131 Select wayline 163
1132 Add way line 163
1133 Wayline AB 165
1134 Wayline curve 167
1135 Wayline A+ angle 171
1136 Wayline Circle 173
1137 Wayline single track 178
1138 Wayline contour segments (optional) 181
1139 Contour segments assistant 185
11310 Contour segments assistant – segment responsible for the wayline 185
11311 Contour segments assistant – management and preview 187
11312 Wayline adaptive curve 187
11313 Manual entry – wayline AB: AB coordinates and height 189
11314 Manual entry – wayline A coordinates + angle 191
11315 Manual entry – wayline circle: Coordinates and height 192
11316 Manual entry – wayline circle: Coordinates, height and radius 199
114 Obstacle 207
1141 Add obstacle 207
1142 Add obstacle point 208
1143 Add obstacle distance – recording 208
1144 Add obstacle distance – record the worked area 212
1145 Add obstacle area – record 214
1146 Add obstacle area – record the worked area 217
1147 Obstacle/marker – deactivate alarm 220
12 Headland 223
121 Headland settings 225
1211 Headland settings 225
1212 Headland settings – GNSS distance calculation to headland boundary for TI
sequence ON (option) 225
1213 AutoTI overlap settings (option) 227
13 Advanced settings/functions 231
131 Advanced settings/functions 233
1311 Receiver upgrade 233
1312 NMEA 0183 233
1313 NMEA 2000 234
Table of contents
VarioGuide Katana
653020070012
1314 Data exchange with a USB stick and data backup 234
132 Operation with the Topcon HiPer AG base station 236
1321 Brief description 236
1322 Scope of delivery and accessories 236
1323 Base station overview 239
1324 LEDs 240
1325 Operating modes 240
1326 Charge battery 241
1327 Set up and connect the base station 241
1328 Operate base station with external battery 242
1329 Switch base station to ON mode 243
13210 Switch base station to STANDBY mode 243
13211 Switch base station to OFF mode 243
14 Faults and remedy 245
141 Fault diagnostics 247
1411 Problems and possible remedial action 247
15 Appendix 251
151 Glossary 253
1511 Glossary 253
16 Index 259
Table of contents
VarioGuide Katana
653020070012
1 Introduction
11 Installation of VarioGuide system 15
Table of contents
VarioGuide
IMAGES PREVIEW OF THE MANUAL:
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the SAME exact manual used by your dealers to fix your vehicle.
- The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
- Any queries / doubts regarding your purchase, please feel free to contact [email protected]
S.M