FENDT NA Harvesting 4300 Pickup Header Operator’s Manual – PDF DOWNLOAD
DESCRIPTION:
FENDT NA Harvesting 4300 Pickup Header Operator’s Manual – PDF DOWNLOAD
1.1 Introduction
1.1.1 Safety symbol
The safety symbol tells you about a potentially hazardous area! Look for the safety symbol in this manual and on the machine. The safety symbols tell you that there is important safety instructions in the manual.
1.1.2 Safety messages
The words DANGER, WARNING or CAUTION are used with the safety symbol. Learn these safety messages and obey the recommended precautions and safety instructions.
DANGER:
If you do not obey the recommended
precautions and safety instructions,
DEATH OR INJURY will occur.
WARNING
If you do not obey the recommended IA CAUTION I
precautions and safety instructions,
DEATH OR INJURY can occur. CMCHE011003530 I
CAUTION:
If you do not obey the recommended
precautions and safety instructions,
INJURY can possibly occur
1.1.3 Information messages
The words important and note are not related to personal safety, and are used to give information about the operation and servicing of the machine.
IMPORTANT: Identifies special instructions or procedures which, if not followed, can cause damage to the machine, the process, or the area around the machine.
NOTE: Information to make procedures easier.
TABLE OF CONTENTS:
FENDT NA Harvesting 4300 Pickup Header Operator’s Manual – PDF DOWNLOAD
1 Safety 7
1 1 Introduction 9
1 1 1 Safety symbol 9
1 1 2 Safety messages 9
1 1 3 Information messages 9
1 1 4 Safety signs 9
1 1 5 A word to the operator 10
1 1 6 This manual 11
1 1 6 1 Operator manual holder 11
1 2 Operation 12
1 2 1 Prepare for operation 12
1 2 2 General information 12
1 2 3 Personal protective equipment 14
1 2 4 Seat instructions 14
1 2 5 Shield and guards 15
1 2 6 Exhaust warning 15
1 2 7 Flying debris 16
1 2 8 Handrails 16
1 2 9 Agricultural chemicals 16
1 3 Travel on public roads 17
1 4 Maintenance 19
1 4 1 General maintenance information 19
1 4 2 Fire prevention and first aid 20
1 4 3 High pressure leaks 21
1 4 4 Tire safety 22
1 4 5 Replacement parts 22
1 5 Cylinder stops 23
1 5 1 Header lift cylinder stop 23
1 5 2 Hold-down cylinder support 23
1 5 2 1 Engage the hold-down cylinder support 23
1 5 2 2 Disengage the hold-down cylinder support 23
1 6 Safety signs 25
2 Introduction 31
2 1 Introduction 33
2 1 1 Units of measurement 33
2 1 2 Replacement parts 33
2 1 3 Intended use 33
2 1 4 Proper disposal of waste 33
2 2 Machine identification 34
2 2 1 Serial number plate 34
2 2 2 Serial number description 34
2 3 Component identification 36
2 4 End shields 38
2 4 1 Open the left side end shield 38
2 4 2 Close the left side end shield 38
3 Operation 41
3 1 Checklists 43
3 1 1 Check the machine before operation 43
Pickup Header
79037387E
Table of contents
3 2 Connect and disconnect the header – Fendt combine 44
3 2 1 Connect the header 44
3 2 2 Disconnect the header 46
3 3 Connect and disconnect the header – Ideal combine 49
3 3 1 Connect the header 49
3 3 2 Disconnect the header 50
3 4 Header transport 53
3 4 1 Transport lamps 53
3 5 Field operation 54
3 5 1 Stop the machine 54
3 5 2 Break in the header 54
3 5 3 Draper speed 55
3 5 4 Header height 56
3 5 5 Pickup height 56
3 5 5 1 Adjust the pickup height 57
3 5 6 Adjust the header floatation 57
3 5 7 Hold-down position 60
3 5 8 Adjust the hold-down rod angle 60
3 5 9 Unplug the header 61
3 5 10 Adjust the pan seal assembly 61
3 6 Auger 63
3 6 1 Auger speed 63
3 6 2 Auger position 63
3 6 3 Adjust the auger position 63
3 6 4 Auger float 64
3 6 4 1 Lock the auger float 64
3 6 4 2 Unlock the auger float 65
3 6 5 Stripper plate clearance 66
3 6 5 1 Examine the stripper plate clearance 66
3 6 5 2 Adjust the stripper plate clearance 67
3 7 Driveline 68
3 7 1 Driveline clutch 68
3 7 2 Driveline guard 68
3 8 Crop deflectors 69
3 8 1 Install the crop deflectors 69
3 8 2 Remove the crop deflectors 70
3 9 Prepare the header for storage 71
4 Maintenance 73
4 1 Service Schedule 75
4 2 Service 76
4 2 1 Prepare the header for service 76
4 2 2 Yearly service 76
4 3 Lubrication 77
4 3 1 Lubricate the machine 77
4 3 2 Lubrication points 78
4 4 End shields 79
4 4 1 Remove the left side end shield 79
4 4 2 Install the left side end shield 80
4 4 3 Remove the right side end shield 81
4 4 4 Install the right side end shield 82
4 4 5 Replace the end shield brackets 83
4 5 Draper belt tension 84
4 5 1 Check the draper belt tension 84
4 5 2 Adjust the front draper belt tension 85
4 5 3 Adjust the rear draper belt tension 86
Pickup Header
79037387E
rra~: •n•11 – Table
of contents
4 6 Draper belts 88
4 6 1 Remove the front draper belt 88
4 6 2 Install the front draper belt 89
4 6 3 Remove the rear draper belt 91
4 6 4 Install the rear draper belt 92
4 6 5 Draper fingers and draper guides 93
4 6 5 1 Replace a draper finger 93
4 6 5 2 Replace a draper guide 93
4 7 Cutterbar seal 95
4 7 1 Adjust the cutterbar seal 95
4 7 2 Remove the cutterbar rubber seal 95
4 8 Driveline 97
4 8 1 Lubricate the header drive shaft 97
4 8 2 Remove the header driveline 97
4 8 3 Install the header driveline 98
4 8 4 Replace the driveline clutch 100
4 8 5 Remove the driveline guard 101
4 8 6 Install the driveline guard 103
4 8 7 Clean the splined shaft 104
4 9 Auger drive 106
4 9 1 Lubricate the auger drive chain 106
4 9 2 Remove the auger drive chain 106
4 9 3 Install the auger drive chain 107
4 9 4 Adjust the auger drive chain tension 108
4 9 5 Remove the driven sprocket 109
4 9 6 Install the driven sprocket 109
4 9 7 Remove the drive sprocket 113
4 9 8 Install the drive sprocket 114
4 10 Auger 116
4 10 1 Replace the auger fingers 116
4 10 2 Replace the auger finger guides 117
4 10 3 Replace the auger finger holders 118
4 10 4 Replace the stripper plates 121
4 10 5 Replace the flighting extensions 121
4 11 Hold down 123
4 11 1 Replace the hold-down rods 123
4 12 Hydraulic 125
4 12 1 Bleed the cylinders and the lines 125
4 13 Electrical 126
4 13 1 Height controllers 126
4 13 1 1 Manually examine the voltage range 126
4 13 1 2 Adjust the header height control voltage range – right-hand side 128
4 13 1 3 Adjust the header height control voltage range – left-hand side 129
4 13 2 Examine the draper speed sensor adjustment 130
4 13 3 Adjust the draper speed sensor 130
4 13 4 Lamps 131
4 13 5 Adjust the transport lamps 131
4 14 Wheels and tires 132
4 14 1 Replace the wheels 132
5 Troubleshooting 135
5 1 Troubleshooting 137
Header dimensions 144
Lubrication specifications 145
7 Assembly 147
7 1 Preparing for assembly 149
7 1 1 Unloadtheheader 149
7 1 2 Lower the header 150
7 2 Assembly 152
7 2 1 Remove the transport hardware 152
7 2 2 Set the rigid wheels to the field position 153
7 2 3 Set the caster wheels to the field position 154
7 2 4 Install the crop deflectors 155
7 2 5 Install the driveline storage bracket 156
7 2 6 Adjust the transport lamps 157
7 2 7 Extend the hold down 158
7 2 8 Change the header opening 158
7 2 9 Reduce the header opening 159
7 2 10 Combine completion kits 162
7 3 Checklists 163
7 3 1 Pre-delivery checklist 163
7 3 2 Delivery checklist 163
8 Index 165
Pickup
IMAGES PREVIEW OF THE MANUAL:
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the SAME exact manual used by your dealers to fix your vehicle.
- The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
- Any queries / doubts regarding your purchase, please feel free to contact [email protected]
S.M