FENDT™ Baler Wrapper Combination Rotana 130 F Combi Rotana 160 V Combi Operator’s Manual – PDF DOWNLOAD
DESCRIPTION:
FENDT™ Baler Wrapper Combination Rotana 130 F Combi Rotana 160 V Combi Operator’s Manual – PDF DOWNLOAD
FENDT Fixed Chamber Baler Rotana 130 F Classic Rotana 130 F Master Rotana 130 F Xtra Operator’s Manual – PDF DOWNLOAD
1.2 Safety Instructions
- YOU are responsible for the SAFE operation and maintenance of your machine.
- YOU must make sure that each person who operates or does work on the machine understands all the SAFETY data in this manual.
- YOU are the key to safety. Good safety procedures prevent accidents to you and each person near you. Make these procedures a set part of your safety sequence.
- Make sure that EVERYONE who operates, does maintenance or works near to the machine obeys the safety precautions.
Follow the safety sequence to prevent the risk of injury or death:
- Owners must complete training with all operators before they operate the machine. This training must be done a minimum of each year
- The operator must read, understand and obey all safety and operation instructions in the manual
- A person who did not read and understand all safety and operation instructions must not operate the machine
- Do not change the equipment. Adjustments not approved by the manufacturer can change the function of the machine and cause damage or personal injury
- Only use approved replacement parts and make sure that only approved technicians do the repair procedures.
1.2.1 General Safety
- Read and understand the manual and all safety decals, before you operate the machine
- Follow all safety regulations, in this manual and instructions or warnings shown on the machine
- Only use the machine for its correct operation
- Only approved persons that understand the operator manual, can operate, drive and do maintenance on the machine
- Keep persons and objects away from parts that move
- Make sure that the installation of all the safety guards and protection devices is correct and they operate correctly
- Always use a tractor with a cabin. Make sure that you close the cabin of the tractor during operation to decrease the quantity of sound. High quantity of sound can cause reduction in hearing
- Always keep a minimum distance of 3 m (10 ft) between the machine and electrical power lines, specially when you open the tailgate
- Know that the height of the machine is up to 3.50 m (11.5 ft) and with an opened tailgate 4.28 m (14.04 ft), depending on specifications and installed tyres
- Put on the correct protective clothing and equipment (gloves, safety glasses and ear protectors)
- Look for hazards and signs of defects (leakage and noise)
- Keep the safety decals clean to make sure that you can see them at all times. Replace safety decals that are missing or you cannot see
- Know the telephone number for emergency medical help in your area
- Speak to your local dealer, if you are not sure of one or more items
- Only connect the machine to the tractor using the procedures in this manual. Only connect the machine to a tractor trailer hitch with your local regulations approval
- Make sure that the front axle weight of the tractor is sufficient. Make sure that you do not have more weight than the maximum permitted on the rear axle
- Do not connect the machine to the tractor when the tractor engine is in operation
- Release the pressure from the hydraulic system before you connect or disconnect the hydraulic hoses. Refer to the manual of the tractor
- If the machine has a pneumatic or hydraulic brake, connect the brake hose(s) to the tractor
- Make sure that all safety guards and protection devices are in position
- Do not remove a blockage by hand or by foot. Always use an applicable tool.
TABLE OF CONTENTS:
FENDT™ Baler Wrapper Combination Rotana 130 F Combi Rotana 160 V Combi Operator’s Manual – PDF DOWNLOAD
1 Safety 7
11 Safety Icons 9
12 Safety Instructions 10
121 General Safety 10
122 Safe Driving 11
123 Safe Driving on Hillsides 11
124 Public Road Transport Safety 11
125 Safe Maintenance 12
126 Safe Operation 12
127 Fire Prevention 13
13 Safety Decals 14
14 Safety Devices 23
141 Emergency Stop Buttons 23
142 Tailgate Safeguard 23
143 Set the Tailgate Safeguard 24
144 Remove the Tailgate Safeguard 24
145 Hydraulic Shut-off Valve 24
146 Net Knife Safeguard 24
147 Install the Net Knife Safeguard 25
148 Remove the Net Knife Safeguard 25
149 Pick-up Safeguard 26
1410 Safety Chain (optional) 26
1411 Film Knife Cover 26
1412 Install the Film Knife Cover 27
1413 Remove the Film Knife Cover 27
1414 Wrapping Ring Safeguard 1 27
1415 Set the Wrapping Ring Safeguard 1 28
1416 Release the Wrapping Ring Safeguard 1 28
1417 Wrapping Ring Safeguard 2 28
1418 Set the Wrapping Ring Safeguard 2 29
1419 Release the Wrapping Ring Safeguard 2 30
1420 Impact Monitor of the Control Unit 30
15 Danger Zones 31
2 Introduction 33
21 Preface 35
211 Manual Contents 35
212 Vehicle Identification Number (VIN) and VIN Plate 35
22 Intended Use 38
221 The Machine 38
222 Correct Use 38
223 Known Misuse 38
23 Description 39
231 General Overview 39
232 Drawbar 39
233 Device to Stop Use Without Approval 40
234 Main Drive Shaft 40
235 Hydraulic System 40
236 Pick-up Unit 41
237 Feed Rotor 41
238 Cutting Unit 41
Table of contents
Baler Wrapper Combination
4900FTEN01
239 Feed Channel Floor 42
2310 Bale Chamber 42
2311 Tying Unit 42
2312 Tailgate 42
2313 Pivoted Roller 42
2314 Bale Transfer 43
2315 Wrapper 43
2316 Wrapping Table 44
2317 Wrapping Ring 44
2318 Stretch Unit 44
2319 Film Knife 44
2320 Cameras 44
2321 Bale Tipper (optional) 45
2322 Bale Mat (optional) 45
24 Controllers 46
241 E-Link Pro 46
242 Keyboard 47
25 E-Link Pro Software 49
251 Home Page E-Link Pro and ISOBUS 50
252 Bale Adjustments Page 53
253 Field Statistics 57
254 Tasks Page 57
255 Advanced Menu 58
3 Operation 65
31 First Use 67
311 Calculate the Maximum Permitted Vertical Load on the Coupling Point 67
312 Calculate the Maximum Permitted Horizontal Load on the Coupling Point 67
313 Adjust the Height of the Drawbar 67
314 Adjust the Power Take-Off (PTO) Shaft 68
315 To Prepare Before You Connect the Power Supply 70
316 Connect the Hydraulics 71
317 Adjustment for Load Sensing System 71
318 Prepare the Chain Lubrication System 72
319 Adjust the Net Roll Holder 72
3110 Adjust the Pre-stretch Rate 73
3111 Adjust the Film Roll Holder for Size 74
3112 Spare Film Rolls 75
3113 Seal Plate (ROTANA 160 V Combi) 75
3114 Setup the E-Link Pro Display 76
3115 Calibration of Wrapper Parts 78
3116 Install the Bale Mat (optional) 78
3117 Install the Bale Tipper (optional) 78
32 Connect the Machine to the Tractor 80
33 Transport Position and Driving 82
331 Transport Position of the Bale Mat (optional) 85
332 Transport Position of the Bale Tipper (optional) 85
333 Apply or Release the Parking Brake 86
334 Place or Remove the Wheel Chocks 87
335 Drain the Air Container of the Pneumatic Brake System 87
34 Prepare the Machine to Bale 88
341 Adjust The Height of the Pick-up 88
342 Adjust the Height of the Wind Guard 89
343 Insert a Net Roll 89
344 Insert the Net 90
345 Move the Pivoted Roller to the Start Position 91
346 Insert the Knives 92
Table of contents
Baler Wrapper Combination
4900FTEN01
347 Set the Correct Number of Knives 92
348 Prepare the Wrapper for Operation 92
349 Insert a New Film Roll 93
3410 Operating Position of the Bale Mat (optional) 94
3411 Operating Position of the Bale Tipper (optional) 95
3412 Adjust the Bale Tipper 96
3413 Adjust the Machine Settings on the Controller 96
3414 Open or Close the Side Covers 97
35 To Operate the Machine 98
351 Check Before You Operate the Machine 98
352 Start Baling and Wrapping 98
353 Make Two or Three Smaller Bales at the End of the Field 99
354 Make One Larger Bale at the End of the Field 99
355 Drive Instructions for Material Intake 99
356 Large Swath 99
357 Small Swath 99
358 Drive on Slopes 101
359 Dry, Brittle, Smooth Crop Material 101
3510 Transfer a Bale 101
3511 Eject a Bale from the Wrapper 102
3512 Remove a Blockage 102
3513 Shut Down Procedure on the Field 103
36 Disconnect the Machine from the Tractor 105
361 Park the Machine 105
362 Remove the Pressure from the Hydraulic System 105
363 Disconnect the Machine 105
364 Support Foot 106
365 Install the Support Foot 107
366 Remove the Support Foot 107
367 To Move the Machine without Brakes 108
368 Take the Machine out of Operation 109
4 Maintenance and Lubrication 111
41 Preventative Maintenance Schedule 113
42 Lubrication Chart 115
43 Clean the Machine 119
44 Chain Lubrication System Maintenance 120
441 Check the Level in the Oil Container of the Chain Lubrication 120
442 Fill the Oil Container 120
443 Bleed Air from the Lubrication Pump 121
45 Roller Lubrication System Maintenance (ROTANA 130 F Combi only) 123
46 Tighten the Chains of the Pick-Up, Bale Chamber and Feed Rotor 124
47 Tighten the Chains of the Wrapper 126
48 Examine the Hydraulic Oil Filter 127
49 Replace the Hydraulic Oil Filter 128
410 Examine the Hydraulic Hoses for Damage and Leaks 129
411 Grind the Cutting Unit Knives 130
4111 Remove the Knives 130
4112 Grind the Knives 131
4113 Install the Knives 131
412 Replace the Knives with Blind Knives 132
4121 Remove the Knives 132
4122 Install the Blind Knives 133
413 Replace the Film Knives 134
414 Adjust and Replace the Belt Guide Pulleys 135
Table of contents
Baler Wrapper Combination
4900FTEN01
415 Adjust the Disk Brake of the Net Tying Unit 136
416 Adjust the Shock Absorbers 137
417 Adjust the Tension Arm of the Wrapping Ring 138
418 Adjust the Tension of the Film Stretching Unit 139
419 Adjust the Wrapper Frame Brake Tension 140
420 Lubricate the Tailgate and Tensioning Arm Rollers (only ROTANA 160 V
Combi) 141
4201 Loosen the Belts 141
4202 Lubricate 141
4203 Tighten the Belts 141
421 Adjusting the Deflectors (only ROTANA 130 F Combi) 143
422 Tensioning the Roller Chains (only ROTANA 130 F Combi) 144
423 Lubricate the Rollers (only ROTANA 130 F Combi) 146
5 Troubleshooting 147
51 Feed Guide Plate 149
52 Manually Remove a Blockage From the Feed Channel Floor 150
53 Bale Optimization (for stable bale sides) 151
54 Prevent Bales of Unusual Shape 152
55 Replace a Transport Wheel 153
551 To Prepare for the Procedure 153
552 Remove the Wheel 153
553 Install the Wheel 154
56 Bale Twisted on the Wrapping Table 155
57 Defective bale shape 156
6 Specifications 157
61 Technical Specifications 159
611 Dimensions 160
62 Shipment 161
621 Lift the Machine 161
622 Attach the Machine to a Truck 162
63 Disposal 163
7 Index 165
Table of contents
Baler Wrapper Combination
4900FTEN01
1 Safety
11 Safety Icons 9
12 Safety Instructions 10
121 General Safety 10
122 Safe Driving 11
123 Safe Driving on Hillsides 11
124 Public Road Transport Safety 11
125 Safe Maintenance 12
126 Safe Operation 12
127 Fire Prevention 13
13 Safety Decals 14
14 Safety Devices 23
141 Emergency Stop Buttons 23
142 Tailgate Safeguard 23
143 Set the Tailgate Safeguard 24
144 Remove the Tailgate Safeguard 24
145 Hydraulic Shut-off Valve 24
146 Net Knife Safeguard 24
147 Install the Net Knife Safeguard 25
148 Remove the Net Knife Safeguard 25
149 Pick-up Safeguard 26
1410 Safety Chain (optional) 26
1411 Film Knife Cover 26
1412 Install the Film Knife Cover 27
1413 Remove the Film Knife Cover 27
1414 Wrapping Ring Safeguard 1 27
1415 Set the Wrapping Ring Safeguard 1 28
1416 Release the Wrapping Ring Safeguard 1 28
1417 Wrapping Ring Safeguard 2 28
1418 Set the Wrapping Ring Safeguard 2 29
1419 Release the Wrapping Ring Safeguard 2 30
1420 Impact Monitor of the Control Unit 30
15 Danger Zones 31
Table of contents
Baler
VIDEO PREVIEW OF THE MANUAL:
IMAGES PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is not a physical manual but a digital manual – meaning no physical copy will be couriered to you. The manual can be yours in the next 2 mins as once you make the payment, you will be directed to the download page IMMEDIATELY.
- This is the same manual used by the dealers inorder to diagnose your vehicle of its faults.
- Require some other service manual or have any queries: please WRITE to us at [email protected]
S.M