MTU Diesel Engine 12V 4000 Gx0 Gx1 16V 4000 Gx0 Gx1 Shop Manual MR20108-01E PDF DOWNLOAD
FILE DETAILS:
MTU Diesel Engine 12V 4000 Gx0 Gx1 16V 4000 Gx0 Gx1 Shop Manual MR20108-01E PDF DOWNLOAD
Language : English
Pages : 533
Downloadable : Yes
File Type : PDF
IMAGES PREVIEW OF THE MANUAL:
TABLE OF CONTENTS:
MTU Diesel Engine 12V 4000 Gx0 Gx1 16V 4000 Gx0 Gx1 Shop Manual MR20108-01E PDF DOWNLOAD
A General
– Important information
– Hazards at the workplace
– Engine side and cylinder designations
– Tightening specifications
– Settings
– Conversion tables
– Publication overview
– Repair of threaded bores through threaded inserts (Heli–Coil)
– Abbreviations
– Keyword index
B Work schedules
– Engine condition check
– W5 Maintenance operations
– Engine removal
– Engine disassembly
– Engine assembly
– Engine run-in
– Engine installation and operation
C Task description
– Group summary
– Materials and consumables
– Tools
– Component removal
– Component disassembly
– Inspection and repair
– Component assembly
– Component installation
VIDEO PREVIEW:
DESCRIPTION:
MTU Diesel Engine 12V 4000 Gx0 Gx1 16V 4000 Gx0 Gx1 Shop Manual MR20108-01E PDF DOWNLOAD
General Assembly Instructions
- Areas of all components that come into contact with oil, fuel, coolant, and combustion air must be clean.
- Components requiring “special cleanness” (e.g., oil and fuel-carrying parts) must be cleaned with suitable cleaning procedures before assembly, checked for particular cleanness, and treated accordingly.
- Component packaging must only be removed immediately before installation.
- Elastomer components (e.g., rubber and similar) must not be washed with diesel fuel, solvent, or cold cleaners.
- Parts dirtied with oil and fuel must be cleaned immediately. The parts should be wiped with a dry cloth.
- Elastomer components such as engine mounts, damping elements, couplings, and V-belts must not be painted. They can only be installed after painting the engine or must be covered before painting work is carried out.
- Radial-lip shaft seals treated by the manufacturer with oil show as a result definite signs of swelling when delivered. They must therefore be cleaned (not washed) only with an abrasion-proof paper cloth before installation.
- The surfaces of parts that slide against each other must be lubricated with SAE30 engine oil when installed unless otherwise specified.
- O-rings and surfaces moving against them during installation (bores and shafts) must be coated with petroleum jelly unless otherwise specified.
- When installing O-rings with counterrings in coolant pumps, always follow the installation instructions.
- After installing O-rings in shaft grooves, in order to remedy twists caused by installation, pass a rounded marking tool under the O-ring in the direction of the circumference if the O-ring diameter is sufficiently large. Make sure that the O-ring is not damaged.
- On the shaft, the sealing lip of the shaft seal must be coated with petroleum jelly, and the shaft running surface with thin-film lubricant or SAE 30 engine oil.
- In the support bore, the outer surface of metal outer jackets – unless otherwise specified in the drawing – must be coated with surface sealant.
- In the case of an elastomer outer jacket or combined metal/elastomer outer jacket, the outer surface must be coated with denatured ethanol.
PLEASE NOTE:
- This is the same manual used by the dealers to diagnose and troubleshoot your vehicle
- You will be directed to the download page as soon as the purchase is completed. The whole payment and downloading process will take anywhere between 2-5 minutes
- Need any other service / repair / parts manual, please feel free to contact [email protected] . We still have 50,000 manuals unlisted
G.P