SCHAEFF TC10Z CRAWLER EXCAVATOR SERVICE MANUAL – PDF DOWNLOAD
VIDEO PREVIEW:
IMAGE PREVIEW:
SCHAEFF TC10Z CRAWLER EXCAVATOR SERVICE MANUAL – PDF DOWNLOAD
SCHAEFF TC10Z CRAWLER EXCAVATOR SERVICE MANUAL – PDF DOWNLOAD
DESCRIPTION:
SCHAEFF TC10Z CRAWLER EXCAVATOR SERVICE MANUAL – PDF DOWNLOAD
- Correct work means the quickest possible completion of according to the correct procedures and the specified standards.
- It is important when conducting certain operations always to bear in mind the equipment, tools, gauges, materials, oil and grease, etc. that you must have ready, as well as items to be checked, adjusted, or disassembled, and cautions to watch out for.
- (1) Never attempt servicing while engine is running or immediately after stopping operation. (2) Wear work cloths, safety shoes and helmet. (3) Check the equipment and tools before use. Especially, be sure to check the crane, lifting equipment and tools.
- (4) When working together with other persons, allocate everyone’s share of job, arrange the signals and act in concert with the other persons. (5) The operation of the crane and slinging work must be performed by qualified persons.
- (6) Do not enter or pass under the raised load. (7) Lift and support the massive parts by crane before removing the installation bolts. (8) Disconnect cables from battery before repairing the electric system.
- (9) Remove the battery when welding the machine. (1) Check the service record of the machine. (That is, check how many months or hours the machine has been used since the preceding overhaul, what was the trouble then and what parts were replaced.)
- (2) Have all servicing tools ready, i.e., tools, measuring devices (which have received periodic maintenance), containers, oil & grease, etc. (3) Have the service literature (operation manual, parts catalog, etc.) ready.
- (1) Clean the machine before disassembly. (2) Check and record the condition of the machine before disassembly : • Model, machine number, operation hours • Reasons for repair, history of repair •
- Contamination of filters • Fuel and oil condition • Damage to parts, etc. (3) Place alignment marks on the necessary parts to facilitate reassembly. (4) Clean all the removed parts and new replacement parts and put them in order. (5) Use new seals, split pins, etc. for reassembly.
TABLE OF CONTENTS:
SCHAEFF TC10Z CRAWLER EXCAVATOR SERVICE MANUAL – PDF DOWNLOAD
COVER...................................................................................... 1 FOREWORD................................................................................... 3 CONTENTS................................................................................... 5 1. General Cautions for Maintenance Work................................................... 11 1-1 Correct Work....................................................................... 11 1-2 Safety Precautions................................................................. 11 1-3 Preparations....................................................................... 11 1-4 Cautions for Disassembly and Reassembly............................................ 11 1-5 Cautions for Removal and Installation of Hydraulic Equipment....................... 12 1-6 Cautions for Removal and Installation of Hydraulic Piping.......................... 12 1-7 Cautions for Handling Seals........................................................ 13 1-8 Correct Installation of Hydraulic Hose............................................. 13 1-9 Specifications of Hydraulic Hose................................................... 16 1-10 Air Release of Hydraulic Equipment................................................ 21 2. Technical Data.......................................................................... 25 2-1 Specifications..................................................................... 25 2-2 Outline Drawing and Working Area................................................... 33 2-3 Weight List of Main Parts.......................................................... 34 2-4 Lifting Capacity List.............................................................. 35 3. Service Standards....................................................................... 39 3-1 Machine Performance................................................................ 39 3-2 Engine............................................................................. 43 3-3 Undercarriage...................................................................... 47 3-3-1 Rubber Crawler Specifications................................................ 47 3-4 Controls........................................................................... 49 3-5 Hydraulic Equipment................................................................ 50 3-5-1 Hydraulic Cylinders.......................................................... 50 3-6 Implement.......................................................................... 51 3-6-1 Front Attachments............................................................ 51 3-6-2 Blade Moving Device.......................................................... 52 3-6-3 Bucket Teeth................................................................. 52 3-7 List of Tightening Torque.......................................................... 53 3-7-1 Machine...................................................................... 53 3-7-2 Engine....................................................................... 55 3-7-3 Tightening Torque for General Bolts and Nuts................................. 55 4. Engine.................................................................................. 59 4-1 Exploded View (General layouts of major engine components)......................... 59 4-2 Measurement, Inspection and Adjustment............................................. 60 4-2-1 Measuring the Compression Pressure........................................... 60 4-2-2 Adjusting the Valve Clearance................................................ 61 4-2-3 Checking the V-belt Tension.................................................. 62 4-2-4 Checking the Fuel Injection Valve............................................ 62 4-2-5 Checking and Adjusting Fuel Injection Timing................................. 64 4-2-6 Adjusting the Maximum (or Minimum) Idling Speed.............................. 69 4-2-7 Checking the Cooling Water System and Radiator for Water Leakage............. 69 4-2-8 Checking the Sensors......................................................... 70 4-3 Measurement Procedure, Service Data and Corrective Action.......................... 71 4-3-1 Cylinder Head................................................................ 71 4-3-2 Cylinder Block............................................................... 76 4-3-3 Valve Rocker Arm............................................................. 78 4-3-4 Piston and Piston Rings...................................................... 80 4-3-5 Connecting Rod............................................................... 83 4-3-6 Cam shaft.................................................................... 86 4-3-7 Crank shaft.................................................................. 87 4-3-8 Gears........................................................................ 90 4-3-9 Trochoid Pump................................................................ 91 4-4 Precautions for Reassembly......................................................... 92 4-5 Electrical Equipment............................................................... 95 4-5-1 Starter Motor................................................................ 95 4-5-2 Alternator................................................................... 96 5. Hydraulic System........................................................................101 5-1 Outline............................................................................101 5-1-1 Control Valve Operation......................................................104 5-2 Hydraulic Circuit Schematic........................................................106 5-2-1 For Standard Type Machines...................................................106 5-3 Circuit Operation..................................................................109 5-3-1 Boom.........................................................................109 5-3-2 Arm..........................................................................111 5-3-3 Bucket.......................................................................113 5-3-4 Swing........................................................................115 5-3-5 Boom Swing...................................................................117 5-3-6 Blade........................................................................119 5-3-7 Travel.......................................................................121 5-3-8 Track Gauge Change...........................................................123 5-3-9 Simultaneous Operation of Travel and Blade...................................125 5-3-10 Simultaneous Operation of Boom Up and Bucket................................127 5-3-11 Hydraulic P.T.O.............................................................129 5-4 Pressure Adjustment................................................................131 5-4-1 System Relief Valves.........................................................131 5-4-2 Circuit Relief Valves........................................................132 5-4-3 Swing Brake Valve............................................................133 5-4-4 Cut-Off Valve................................................................134 6. Hydraulic Equipment.....................................................................137 6-1 Hydraulic Pump.....................................................................137 6-1-1 S/N 28645 and before.........................................................137 6-1-2 S/N 28646 and above..........................................................163 6-2 Control Valve......................................................................181 6-3 Pilot Valve........................................................................201 6-4 Cut-off Valve......................................................................216 6-5 Swing Motor........................................................................227 6-6 Travel Motor.......................................................................244 6-6-1 S/N 22644 and before.........................................................244 6-6-2 S/N 22701 and above..........................................................271 7. Adjustment and Repair...................................................................309 7-1 Electrical Equipment and Engine of Machine.........................................309 7-1-1 Parts Layout of Electrical Equipment.........................................309 7-1-2 Monitor and Alarm Systems....................................................310 7-1-3 Wiring Diagram...............................................................317 7-1-4 Circuit Description of Engine Start and Stop.................................318 7-1-5 Removal and Reinstallation of Engine.........................................321 7-1-6 Removal and Reinstallation of Starter Motor..................................326 7-1-7 Removal and Reinstallation of Fuel Injection Pump............................328 7-1-8 Removal and Reinstallation of Fuel Tank......................................330 7-1-9 Removal and Reinstallation of Radiator.......................................332 7-2 Undercarriage......................................................................334 7-2-1 Outline......................................................................334 7-2-2 Points of Reassembly.........................................................335 7-2-3 Removal and Reinstallation of Crawler........................................337 7-2-4 Disassembly and Reassembly of Idler..........................................338 7-2-5 Disassembly and Reassembly of Track Roller...................................341 7-2-6 Removal and Reinstallation of Track Gauge Change Cylinder....................344 7-3 Controls...........................................................................347 7-3-1 Control Train................................................................347 7-3-2 Mechanical Control Linkage...................................................348 7-3-3 Adjustment of Control Levers.................................................350 7-3-4 Adjustment of Travel and Blade Levers........................................351 7-3-5 Adjustment of Boom Swing and P.T.O. Pedals and P.T.O. Pedal Lock.............352 7-3-6 Adjustment of Lock Lever Switch..............................................353 7-3-7 Adjustment of Accelerator Lever..............................................354 7-4 Swing Bearing......................................................................356 7-4-1 Removal and Reinstallation of Swing Bearing..................................356 7-5 Hydraulic Equipment................................................................358 7-5-1 Removal and Reinstallation of Hydraulic Oil Tank.............................358 7-5-2 Removal and Reinstallation of Control Valve..................................361 7-5-3 Removal and Reinstallation of Swing Motor....................................364 7-5-4 Removal and Reinstallation of Swivel Joint...................................366 7-5-5 Disassembly and Reassembly of Swivel Joint...................................369 7-5-6 Disassembly and Reassembly of Hydraulic Cylinders............................372 7-5-7 Removal and Reinstallation of Boom Swing Cylinder............................376 7-5-8 Removal and Reinstallation of Hydraulic Oil Tank.............................379 7-5-9 Piping Layout................................................................383 7-6 Implement..........................................................................391 7-6-1 Removal and Reinstallation of Implement......................................391 8. Periodic Inspection and Servicing.......................................................401 8-1 List of Periodic Inspection and Servicing..........................................401 9. Fuel, Lube Oil and Grease Recommended...................................................405 10. Troubleshooting........................................................................409 10-1 Non-Breakdowns....................................................................409 10-1-1 Natural Release of Bucket...................................................409 10-1-2 Discontinuous Arm Movement..................................................409 10-1-3 Drifting of Upperstructure on Quick Travel Operation........................410 10-1-4 Thermal Shock of Travel Motor...............................................411 10-1-5 Change of Blade Speed in Loaded Condition...................................412 10-1-6 Time Lag on Travel Speed Switching..........................................413 10-1-7 Fluctuation in Oil Level of Hydraulic Oil Tank Due to Temperature Change....414 10-2 Troubleshooting...................................................................415 10-2-1 Machine and Engine..........................................................415 10-2-2 Electrical Equipment on Panel...............................................436 11. Reference Data.........................................................................447 11-1 Specifications for Attachment.....................................................447
PLEASE NOTE:
- This is the same manual used by the DEALERSHIPS to SERVICE your vehicle.
- The manual can be all yours – Once payment is complete, you will be taken to the download page from where you can download the manual. All in 2-5 minutes time!!
- Need any other service / repair / parts manual, please feel free to contact us at heydownloadss @gmail.com . We may surprise you with a nice offer
