Scania Industrial and Marine Engines 16 litre engine Work Description Manual – PDF DOWNLOAD
DESCRIPTION:
Scania Industrial and Marine Engines 16 litre engine Work Description Manual – PDF DOWNLOAD
SAMPLE PAGES FROM THE MANUAL:
General
DC engine:
The prefilter and paper filter must be renewed as described in the maintenance instructions. The system is fitted with a fluid trap. There must always be oil in the fluid trap. If the system has been emptied, pour approximately 1 dl oil on the bottom of the filter housing to fill the fluid trap.
- Blow-by is the flow of gases through the engine crankcase and out via the crankcase ventilation. The closed crankcase ventilation system is very sensitive for changes to the blow-by in the engine. If the blow-by increases, the amount of gas passing through the crankcase ventilation will also increase. The crankcase gases can then take with it small drops of oil from the crankcase.
- When the amount of oil increases, the oil separator will not be able to fulfil its task of separating the oil. Oil will then accompany the air into the charge air system. Causes of an increase in blow-by are leaking piston rings, valve guides, turbocharger or compressor. – Too much oil in the oil sump If the engine is filled with too much oil, the excess will splash around in the crankcase and be atomized.
- This means that the crankcase gases will contain a large amount of atomized oil that the crankcase ventilation will not be able to separate the oil properly. This will result in a large amount of oil from the crankcase ventilation.
TABLE OF CONTENTS:
Scania Industrial and Marine Engines 16 litre engine Work Description Manual – PDF DOWNLOAD
General 4
Specifications 4
General tightening torques5
Removing and lifting the engine 6
Special tools 6
Lifting and fitting the engine8
Mounting the engine in a universal stand 9
Special tools 9
Cylinder head 10
Adjusting the valve clearance and unit injectors11
Adjusting the valve clearance 12
Adjusting the unit injector 12
Order of adjustment15
Renewing the upper rocker cover gasket16
Renewing the lower rocker cover gasket16
Cylinder head 20
Removal 20
Fitting 24
Valves30
Removal 30
Fitting 30
Checking and machining31
Valve stem seal 32
Renewal 32
Valve seats 33
Renewal 33
Machining the cylinder head 35
Specifications 35
Work description 37
Valve guides 39
Renewal 39
Sleeves for unit injectors 40
Renewal 40
Cylinder block 42
Overhaul 42
Cylinder liner 43
Removal 43
Fitting 44
Measuring the cylinder liner height45
Machining cylinder liner height 47
Rear crankshaft seal 52
Renewal 52
Flywheel housing53
Removal 53
Fitting 54
Closed crankcase ventilation 56
Front timing gear casing 58
Removal 58
Fitting 59
Front crankshaft seal 60
Renewal 60
Crank mechanism62
Piston and connecting rod 63
Removal 63
Fitting 64
Renewing a piston 66
Connecting rod 69
Checking 69
Renewal of bearing bushing in connecting rod 71
Flywheel 73
Removal 73
Fitting 74
Support bearing75
Ring gear 76
Crankshaft 77
Removal 77
Fitting 79
Checking and machining the crankshaft 82
Timing gear84
Gear drive84
Intermediate gear86
Removal 86
Fitting 88
Bearing in intermediate gear 89
Camshaft gear 92
Crankshaft gear 93
Camshaft 95
Removal 95
Fitting 98
Checking camshaft setting 101
Removing the camshaft bearing 102
Fitting the camshaft bearing 106
Fan drive 110
Lubrication system 114
Oil filter 114
Oil cooler116
Oil cleaner 118
Oil pump122
Exhaust manifold 124
Turbocharger 125
VIDEO PREVIEW OF THE MANUAL:
IMAGES PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the SAME manual used by the dealers to troubleshoot any faults in your vehicle. This can be yours in 2 minutes after the payment is made.
- Contact us at [email protected] should you have any queries before your purchase or that you need any other service / repair / parts operators manual.
Ezequiel Maximilian –
quick and easy