FENDT Large Square Baler 1290 UD Workshop Service Manual – PDF DOWNLOAD

TABLE OF CONTENT
General 1
Main frame 2
Drive system 3
Hydraulic system 4
Electrical system 5
Bale feed system 6
Bale forming system 7
Roller bale chute system 8
Diagrams 9
Index 10

11 Safety
111 Safety symbol
112 Safety messages
113 Information messages
114 Safety signs
115 Safety warnings
116 A w ord to the technician
117 The service manual
118 The operator manual
119 Tool box
1110 Operation
11101 General information
11102 Prepare for operation
11103 Personal protective equipment
11104 Seat instru ctions
11105 Shield and guards
11106 Exhaust warning
11107 Flying debris
11108 Handrails
11109 Agricultural che mical s
1111 Travel on public roads
1112 Maintenance
11121 General maintenan ce information
11122 Fire prevention and first aid
11123 High pressure leaks
11124 Tire safety
12 General information
121 Introdu ction to this service manual
122 Units of measurement
123 Table of contents
124 Page numbers
125 Remove a gib key
126 Install a gib key
127 Remove a lock collar
128 Install a lock collar
13 Specifications
131 Specifications
1311 Dimensions and weights
1312 Drive system specificati ons
1313 Shearbolt specifications
1314 Hydraulic specificati ons
1315 Pickup specifications
1316 Packer specifications
1317 Stuffer specifications
1318 Plunger specifications
1319 Tw ine specifi cations
13110 Knotter and needle specification s
13111 Bale chamber tension specifications
13112 Ejector specifications
13113 Roller bale chute specifications
1311 4 Lamp specifications
13115 Knott er lubrication pump specifi cati ons
1-26
13116 Chain lubricati on pump specificati ons
1-26
13117 Lubricants and capacities
1-26
13118 Tire specifications
1-27
13119 Brake specificati ons
1-28
13120 M aximum speed
1-28
13 121 Tractor requirement s
1-28
13122 Noise level
1-28
132 Bolt torque values
1-28
14 Machine indentification
1-31
141 Location of the serial number plates and the statutory plates – if necessary
1-31
142 Serial number description
1-32
15 Machine component view s
1-33
151 Outside view – left side
1-33
152 Outside view – right side
1-34
153 Inner view – left side
1-35
154 Inner view – right side
1-36
155 Outside view – top
1-37
156 Outside view – bottom
1-38
16 Service and lubrication schedule
1-39
161 Servi ce schedule
1-39
162 Lubri cation procedures and general information
1-42
1621 Drive chains
1-42
1622 Driveline lubrication and maintenance
1-43
1623 Lubricate the hitch ball, if equipped
1-45
1624 Do not lubricate the overrunning clutch
1-45
1625 Do not lubricate the slip clutch for the main drive
1-46
1626 Lubricate the connecting rods
1-46
1627 Examine the packer crank bearings
1-46
1628 Lubricate the bearing for the main drive sprocket
1-47
1629 Lubricate the stuffer drive
1-47
16210 Lubricate the knotter/needle clutch arm and the clutch arm roller
1-47
16211 Lubricate the brake linkages
1-48
16212 Lubricate the steering axle pivots and the steering axle tie-rods
1-48
16213 Lubricate the pivot bushings for the tandem axle spring s
1-49
16214 Lubricate the center fitting for the six twine knotter
1-49
16215 Lubricate the linkages for the bale density cylinders
1-49
16216 Lubricate the packer clutch bushing and the splines
1-50
17 Connect to the tractor – CE
1-51
171 Hitch component identification
1-51
172 Set the tongue height 1-51
173 Tractor setup dimensions w ith an 80 mm (315 in) ball hitch, a CE spherical ball hitch,
or
a 50 mm (2 in) ring hitch
1-52
174 Connect a 50 mm (2 in) ring hitch to the tractor
1-52
175 Connect an 80 mm (315 in) ball hitch to the tractor
1-53
176 Operate a manual jack installed on the tongue
1-53
177 Operate a hydrauli c jack installed on the tongue
1-54
178 Install the safety transport chain
1-55
179 Constant velocity implement driveline, if equipped
1-55
1791 Check the constant velocity implement driveline for correct length
1-55
1792 Connect a constant velocity implement driveline to a pow er take-off (PTO) 1-57
1793 Adjust the pedestal gearbox
1-58
18 Checklists
1-59
18 1 Daily checklist
1-59
182 Examine after the first hour of operation
19 Lamps and Reflectors
191 Lamps and reflectors
192 Lamps and reflectors
110 Baler operation
1101 Description of operation 1-67
1102 General terminal information 1-67
1103 Prepare to bale
1104 Plunger position indication
1105 Start the machine
11051 Start the machine: determine the direction of plunger travel
11052 Start the machine: plunger on the retraction (green) stroke 1-70
11053 Start the machine: plunger on the compression (red) stroke 1-71
11054 Start the machine: machine does not start after four attempts 1-71
1106 Make the first bale 1-72
1107 Make bales 1-73
1108 Stop the machine 1-73
1109 Stuffer cycle 1-74
111 Prepare to road the machine or move the machine on a trailer 1-75
112 Tie down points, jack points, and lift points 1-77
1121 Tie down points 1-77
1122 Jack points
1-78
1123 Lift points
1-78
1124 Lift and move a machine correctly 1-78
113 Disconnect the tractor
1-80