Daewoo Doosan MicroController Control System B20S-5 to BC25SE-5 Testing Adjusting Manual SB4200E00

Description

Daewoo Doosan MicroController Control System B20S-5 to BC25SE-5 Testing Adjusting Manual SB4200E00 – PDF DOWNLOAD

FILE DETAILS:

Daewoo Doosan MicroController Control System B20S-5 to BC25SE-5 Testing Adjusting Manual SB4200E00

Language :English
Pages :182
Downloadable : Yes
File Type : PDF

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

Daewoo Doosan MicroController Control System B20S-5 to BC25SE-5 Testing Adjusting Manual SB4200E00

MicroController Control Systems
B20S-5, B25S-5, B30S-5, B32S-5
BC20S-5, BC25S-5, BC30S-5, BC32S-5
BC25SE-5
for Electric Lift Trucks

Important Safety Information
Most accidents involving product operation, maintenance and repair are caused by failure to observe basic safety
rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an
accident occurs. A person must be alert to potential hazards. This person should also have the necessary training,
skills and tools to perform these functions properly.
Improper operation, lubrication, maintenance or repair of this product can be dangerous and could result
in injury or death.
Do not operate or perform any lubrication, maintenance or repair on this product, until you have read and
understood the operation, lubrication, maintenance and repair information.
Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not
heeded, bodily injury or death could occur to you or other persons.
The hazards are identified by the “Safety Alert Symbol” and followed by a “Signal Word” such as “WARNING” as
shown below.
The meaning of this safety alert symbol is as follows:
Attention ! Become Alert ! Your Safety is Involved.
The message that appears under the warning, explaining the hazard, can be either written or pictorially presented.
Operations that may cause product damage are identified by NOTICE labels on the product and in this publication.
DOOSAN cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in
this publication and on the product are therefore not all inclusive. If a tool, procedure, work method or operating
technique not specifically recommended by DOOSAN is used, you must satisfy yourself that it is safe for you and
others. You should also ensure that the product will not be damaged or made unsafe by the operation, lubrication,
maintenance or repair procedures you choose.
The information, specifications, and illustrations in this publication are on the basis of information available at the
time it was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other
items can change at any time. These changes can affect the service given to the product. Obtain the complete
and most current information before starting any job. DOOSAN dealers have the most current information
available.

TABLE OF CONTENTS:

Daewoo Doosan MicroController Control System B20S-5 to BC25SE-5 Testing Adjusting Manual SB4200E00

Specifications
Assembly Layout of Controller 10
Assembly Layout of Motors (36/48/80 V) 10
B20/25/30/32S-5 Motors 8
BC20/25/30/32S-5 Motors 7
Component Measurements 5
Controller AS Specification 6
Control Panel Layout 11
Fuses 10
Instrument Panel Layout 9
Systems Operation
General Information 14
Glossary 12
Installation and Wiring 18
Testing and Adjusting
B20/25/30/32S-5 43
BC20/25/30/32S-5 31
Preparation Tests and Check 27
Programmable Parameters 30
Some Functions Management 48
Diagnostic and Troubleshooting
Alarm List 49
Electrical System Adjustment 101
General Description 49
System Tests and Adjustments 100
Troubleshooting Problem List 58
Instrument Panel
Accessing Stored Error Codes 121
Default Setting 118
Diagnostic Mode 119
Display Keys Utilization 108
Instrument Panel 104
List of diagnostic 120
Parameter Calibration 109
Sensor Initial Setting 118
Eye Software Interface
General Information124
Installation 125
Features 126
Main Menu128
Troubleshooting of Eye Program 158
Appendix
Appendix A : 36[V] Parameter List 159
Appendix B : 48[V] Parameter List 162
Appendix C : 80[V] Parameter List165
Appendix D : Parameter List 168
Appendix E : Error Code List171
Appendix F : Contraction for dot matrix display 177
F1 Alarm Code 177
F2 Calibration Code 178
F3 Diagnostic Code 180

S.M 20/2/2025