Class SOYBEAN CUTTERBAR 4.50 M- 9.00 M LEXION 580 – 510 Operator’s Manual- PDF DOWNLOAD
DESCRIPTION:
INTRODUCTION
Class SOYBEAN CUTTERBAR 4.50 M- 9.00 M LEXION 580 – 510 Operator’s Manual- PDF DOWNLOAD
- This manual is valid for the CLAAS Soybean Cutterbar for Lexion 580 – 510. It is intended primarily for the machine operator and provides information concerning the use, adjustment and operation of the cutterbar.
- For commissioning the Soybean Cutterbar, see the combine harvester operating instructions The advice on care and servicing should be followed in order to obtain maximum performance and long service from the Soybean Cutterbar.
- In addition, regular inspections of the machine should be carried out by your CLAAS specialist workshop. Neglect in maintenance or service, and incorrect use will result in poor machine efficiency and loss of time.
- This manual is only valid in conjunction with the combine harvester’s operating instructions.
TABLE OF CONTENTS:
Class SOYBEAN CUTTERBAR 4.50 M- 9.00 M LEXION 580 – 510 Operator’s Manual- PDF DOWNLOAD
Introduction ......................................................................... 5 Introduction ..................................................................... 7 Table of contents .................................................................... 9 Table of contents ................................................................11 General information ..................................................................13 Special care .....................................................................15 Identification plate .........................................................17 Safety rules .........................................................................19 Safety rules .....................................................................21 Cylinder safety lock .........................................................23 Feeder housing ...........................................................23 Reel .....................................................................23 Safety decals with pictorials ....................................................25 Prior to operation ...................................................................31 Carry out before initial operation ...............................................33 Removing the transport fixtures ..............................................33 Adjusting the cutterbar flotation springs ....................................33 Fitting the right-hand cutterbar cylinder ....................................33 Fitting a third cutterbar cylinder ...........................................33 Coupling section for machines with CLAAS Contour (without transverse control) ....35 Fitting the coupling section .................................................35 Operation - Cutterbar ................................................................37 Mounting the cutterbar ...........................................................39 Adjusting the hydraulic cylinder for transverse control of the cutterbar .....39 Connecting the universal drive shaft .........................................40 Fitting the quick-release coupling ...........................................41 Unmounting the cutterbar .....................................................41 Adjusting the cutterbar ..........................................................43 Cutterbar skids ..............................................................43 Reel .........................................................................43 Reel tines ...................................................................44 Horizontal reel adjustment ...................................................45 Knife ........................................................................45 Standard knife system ........................................................46 Standard knife system settings ...........................................47 SG3/S and SG3 knife systems ..................................................48 SG3/S and SG3 knife system adjustment ........................................48 Intake auger .................................................................49 Adjusting the clearance to the bottom plate ..............................49 Adjusting the feed finger control ............................................49 Changing the inclination of the cutter bar ...................................50 Crop dividers ................................................................52 Adjusting the divider points .............................................52 Basic crop divider setting ...................................................53 Replacing the divider points .................................................54 Fitting the insert for long divider points ...................................55 Conversion from soybeans to grain ................................................57 Removing the soybean sensor ..................................................57 Fitting the sensor bands .....................................................58 Changing over the sensors and adjustment .....................................58 Adjusting the sensor actuating levers to the end stops .......................59 Arresting the cutter bar .....................................................60 Conversion from grain to soybean .................................................61 Changing over the sensors and adjustment .....................................61 Adjusting the sensor actuating levers to the end stops .......................62 Fitting the soybean sensor ...................................................63 Unlocking the outer runner of the control arm ................................63 Remove stop bolts for cutter beam ............................................64 Maintenance ..........................................................................65 Maintenance and lubricant table ..................................................67 Maintenance schedule .........................................................67 Lubricants chart .............................................................68 Knife drive gearbox ..............................................................69 Checking the oil level / oil change ..........................................69 Adjusting the drive support ..................................................70 Adjusting the spring cylinder ................................................70 Drive belts / drive chains .......................................................71 Removing the knife drive belt (40) ...........................................71 Fitting the knife drive belt (40) ............................................72 Tensioning the intake auger drive chain (41) .................................72 Tensioning the reel drive ....................................................72 Inductive sensor for reel drive ..............................................73 Lubrication chart ....................................................................75 Lubricants and notes .............................................................77 Index ................................................................................81 Index ............................................................................83 A ............................................................................83 B ............................................................................83 C ............................................................................83 D ............................................................................83 F ............................................................................83 H ............................................................................83 I ............................................................................83 K ............................................................................83 L ............................................................................83 M ............................................................................83 R ............................................................................83 S ............................................................................83 T ............................................................................83 U ............................................................................83
IMAGES PREVIEW OF THE MANUAL:
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the same manual used by the DEALERSHIPS to SERVICE your vehicle.
- The manual can be all yours – Once payment is complete, you will be taken to the download page from where you can download the manual. All in 2-5 minutes time!!
- Need any other service / repair / parts manual, please feel free to contact us at heydownloadss @gmail.com . We may surprise you with a nice offer
S.M