CLAAS TARGO K SERIES Operator’s Manual – PDF DOWNLOAD
DESCRIPTION:
CLAAS TARGO K SERIES Operator’s Manual – PDF DOWNLOAD
GENERAL DESCRIPTION
- The CLAAS range of telehandlers has a modern design that enables the machine to be operated over different terrain whilst utilizing a wide variety of CLAAS approved front mounted attachments.
- The driver’s cab is fully glazed, compliant with ROPS/FOPS legislation, and features excellent control layout and operator ergonomics. It can be complemented with the addition of air conditioning and other accessories including an air suspension seat.
- The seat mounted electro-hydraulic joystick enables simultaneous operation of 3 hydraulic functions, proportionally, for simple and precise operation of the boom.
- An ultra low boom design and curved front screen combine to provide unbeatable visibility all around the machine and to the attachment as it is raised to any height.
- A limited slip differential in the front axle, together with four wheel drive and a choice of agricultural or industrial tyres enable the machine to operate on many typical surfaces
Introduction to the Handbook
The contents of the Operators Handbook are intended as a guide to the operation and servicing of the CLAAS telehandler range. The general method of operation of all these machines is the same. Any individual differences in the specification or operation are detailed separately
Note:
- The procedures and illustrations contained in this manual refers to all models. Some illustrations may differ slightly from the actual machine
- This handbook is not a training manual. It is designed as a guide to the machine’s controls and working capacities and general maintenance only. It must not be removed from the machine and should be kept clean and in good condition. Additional copies of the handbook can be obtained from your CLAAS dealer.
- Only trained operators should use this machine. CLAAS strongly recommends that anyone who is responsible for the operation and servicing of this machine be fully trained in its safe operation.
- If you have any doubts about any aspects of the machine’s capability or servicing procedures, you must consult CLAAS through your local CLAAS dealer.
- Throughout this handbook and on the machine there are safety notes. Each note starts with a single word. The meaning of these single words are explained below.
TABLE OF CONTENTS:
CLAAS TARGO K SERIES Operator’s Manual – PDF DOWNLOAD
GENERAL DESCRIPTION
INTRODUCTION
Introduction to the handbook
Running in
Machine identification
Safety section
Safety messages
General hazards
SECTION 1
Before driving the machine – Safety warnings 11
Entering the cab 12
Emergency exit 13
Adjusting the seat 14
Adjusting the steering column and joystick mounting 15
Cab layout and Controls 16
Instruments and warning lights 19
Facia mounted switches 111
Steering column switches 112
Side console switches 113
Boom and carriage controls 114
Auxiliary controls 115
Steering modes 116
Starting and Stopping the engine 117
Engaging gears – APC Powershift 119
Engaging gears – powershift 122
Driving the machine 123
Reversible cooling fan 125
Working the Telehandler 128
Longitudinal Stability Indicator 128
Examples of instability situations 130
Lifting envelope 131
Approaching a load – Working with pallet forks 133
Picking up a load – Working with pallet forks 134
Placing a load – Working with pallet forks 136
Lifting unpalletised loads 137
Travelling 138
Transporting the machine 139
SECTION 2
Attachments – fitting and removal 21
Hydraulically operated attachments 23
Working with front end attachments 24
Automatic trailer pick-up hitch (Auto-hitch) 25
Manual trailer pick-up 27
Extension jibs and crane hooks 28
CONTENTS
SECTION 3
Safety Warnings 31
Access to service checkpoints 32
Service schedule 33
Grease points 36
Wheels and tyres 37
Engine oil level 38
Engine oil and filter 39
Cooling system 310
Fuel system 314
Air cleaner 318
Engine 319
Fan drive system 320
Transmission and Transfer Box 321
Axles 324
Hydraulics 325
Battery 328
Auto-hitch 329
Rockinger hitch 329
Windscreen washer bottle 329
Cab and engine compartment 330
SECTION 4
Machine specifications 41
Adjustments 42
Lubricants and fluid specifications 42
Capacities – fluid 43
Pressures 43
Dimensions – machines fitted with standard tyres 44
Fusebox 45
CONTENTS
CONTENTS
SECTION 4 (continued)
Sheet 4 – Head/side lights, fog lights, number plate lights, head flasher 425
Sheet 4A – Head/side lights, fog lights, number plate lights, head flash 426
Sheet 5 – Turn indicators, reverse lamps, steer sensors, top lights, radio 427
Sheet 6 – Inst display, sensor switches, fan motor, aircon, interior light, beacon,
fuel sender, fan reverse, hyd temp 428
Sheet 7 – APC 50 with ign controlled APC bat feed, screened sensor cable, p/brake link 429
Sheet 7A – Non-APc, correct p/brake and trans dump, no p/brake controller, cicuit link 430
IMAGES PREVIEW OF THE MANUAL:
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the same manual used by the dealers to diagnose and troubleshoot your vehicle
- You will be directed to the download page as soon as the purchase is completed. The whole payment and downloading process will take anywhere between 2-5 minutes
- Need any other service / repair / parts manual, please feel free to contact [email protected] . We still have 50,000 manuals unlisted
S.M