Case Magnum 225 250 280 310 Series Tractor Shop Manual – PDF Download

Case Magnum 225 250 280 310 Series Tractor Shop Manual – PDF Download

IMAGES:

TABLE OF CONTENTS:

NOTE: Engine repair information is not contained within this tractor Service Manual For engine repair, refer to
publication number 87518866 for the 83 & 90L 6 Cylinder, 24 Valve CNH Engine with High Pressure Common
Rail Fuel System
STANDARD TORQUE SPECIFICATIONS SECTION 1000
TORQUE SPECIFICATIONS – METRIC HARDWARE 1000-4
TORQUE SPECIFICATIONS – STEEL HYDRAULIC FITTINGS 1000-5
TORQUE SPECIFICATIONS – STEEL HYDRAULIC FITTINGS 1000-6
SAFETY, GENERAL INFORMATION, MAINTENANCE SCHEDULE SECTION 1001
SAFETY 1001-3
GENERAL INFORMATION 1001-5
LUBRICATION/MAINTENANCE CHART 1001-6
SYSTEM CAPACITIES 1001-7
COOLING SYSTEM MODULE REMOVAL AND INSTALLATIONSECTION 2001
COOLING SYSTEM MODULE REMOVAL 2001-3
COOLING SYSTEM MODULE INSTALLATION 2001-7
ENGINE REMOVAL AND INSTALLATIONSECTION 2002
SPECIAL TORQUES 2002-3
ENGINE REMOVAL 2002-4
ENGINE INSTALLATION 2002-21
VISCOUS FAN DRIVE TESTSECTION 2003
REQUIRED TOOLS 2003-3
DIAGNOSTIC PROCEDURE 2003-4
FAN SPEED TEST 2003-7
FUEL TANK / FUEL SENDER REMOVAL AND INSTALLATIONSECTION 3001
SPECIAL TORQUES 3001-3
FUEL TANK REMOVAL AND INSTALLATION 3001-3
FUEL LEVEL SENDER REMOVAL AND INSTALLATION 3001-10
ELECTRICAL SCHEMATIC POSTER – EUROPEAN87389709
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
3
ELECTRICAL SYSTEM – HOW IT WORKS AND TROUBLESHOOTINGSECTION 4001
SPECIAL TOOLS 4001-4
FUSES AND RELAY IDENTIFICATION 4001-5
Cab Fuses/Relay Location 4001-5
Engine Compartment Fuse/Relay Identification (Power Distribution Box) 4001-5
Fuse Identification 4001-6
Relays 4001-7
INSTRUMENTATION AND CONTROLS 4001-8
CONNECTOR AND COMPONENT LOCATIONS 4001-12
ELECTRICAL CONNECTORS 4001-35
ELECTRICAL SYSTEMS SCHEMATICS AND DIAGNOSTICS 4001-142
Power Distribution System Circuit Operation 4001-142
Power Distribution Circuit Troubleshooting 4001-142
Power Distribution Schematic 4001-142
POWER DISTRIBUTION SYMPTOM CHART 4001-143
Diagnostic Tests 4001-144
AUDIO SYSTEM 4001-146
Audio System Circuit Operation 4001-146
Audio System Circuit Troubleshooting 4001-146
Audio System Symptom Chart 4001-146
Audio System Diagnostic Tests 4001-148
CHARGING SYSTEM 4001-152
Charging System Circuit Operation 4001-152
Charging System Circuit Troubleshooting 4001-152
Charging System Symptom Chart 4001-153
Charging System Diagnostic Tests 4001-154
EXTERIOR LIGHTING SYSTEM 4001-158
Exterior Lighting System Circuit Operation 4001-158
Exterior Lighting System Circuit Troubleshooting 4001-158
Exterior Lighting System Symptom Chart 4001-159
Exterior Lighting System Diagnostic Tests 4001-159
INSTRUMENTATION AND WARNING SYSTEM 4001-164
Instrumentation and Warning System Circuit Troubleshooting 4001-164
Instrumentation and Warning System Symptom Chart 4001-164
Instrumentation and Warning System Diagnostic Tests 4001-165
INTERIOR LIGHTING AND HORN SYSTEM 4001-168
Interior Lighting and Horn System Circuit Operation 4001-168
Interior Lighting and Horn System Circuit Troubleshooting 4001-168
Interior Lighting and Horn System Symptom Chart 4001-169
Interior Lighting and Horn System Diagnostic Tests 4001-169
POWER MIRROR SYSTEM 4001-173
Power Mirror Circuit Operation 4001-173
Power Mirror Circuit Troubleshooting 4001-173
Power Mirror System Symptom Chart 4001-174
Power Mirror System Diagnostic Tests 4001-176
POWER SEAT SYSTEM 4001-185
Power Seat System Circuit Operation 4001-185
Power Seat System Circuit Troubleshooting 4001-185
Power Seat System Symptom Chart 4001-186
Power Seat System Diagnostic Tests 4001-187
STARTING SYSTEM 4001-191
Starting System Circuit Operation 4001-191
Starter Motor Circuit Troubleshooting 4001-191
Starting System Symptom Chart 4001-191
Starting System Diagnostic Tests 4001-193
WIPER/WASHER SYSTEM 4001-198
Wiper/Washer System Circuit Operation 4001-198
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
4
Wiper/Washer System Circuit Troubleshooting 4001-198
Wiper/Washer System Symptom Chart 4001-199
Wiper/Washer System Diagnostic Tests 4001-200
STEERING COLUMN AND STEERING HAND PUMPSECTION 5001
SPECIAL TOOLS 5001-2
SPECIAL TORQUES 5001-3
STEERING COLUMN AND STEERING HAND PUMP 5001-3
REMOVAL 5001-3
STEERING HAND PUMP SERVICE 5001-7
STEERING COLUMN ASSEMBLY 5001-9
INSTALLATION 5001-10
POWERSHIFT TRANSMISSION SYSTEM – HOW IT WORKS AND TROUBLESHOOTINGSECTION 6000
TRANSMISSION SYSTEM INTRODUCTION 6000-3
TRANSMISSION SYSTEM CONTROLS 6000-5
TRANSMISSION SYSTEM COMPONENTS 6000-6
TRANSMISSION LUBE AND DISTRIBUTION TUBES 6000-8
POWERSHIFT TRANSMISSION CLUTCH LAYOUT 6000-10
POWERSHIFT VALVE CLUTCH ENGAGEMENTS 6000-11
POWER FLOW (REVERSE SPEEDS) 6000-30
POWER FLOW (REVERSE SPEEDS) 6000-32
POWER FLOW (FORWARD CREEPER DRIVE SPEEDS) 6000-34
POWER FLOW (REVERSE CREEPER DRIVE SPEEDS) 6000-40
INCHING VALVE OPERATION 6000-42
INSTRUMENTATION CLUSTER – TRANSMISSION LEAKAGE CHECK 6000-46
MASTER CLUTCH PRESSURE CHECK 6000-49
TRANSMISSION INPUT SHAFT AND DRIVE PLATESECTION 6001
SPECIAL TORQUES 6001-3
TRANSMISSION INPUT SHAFT AND DRIVE PLATE REMOVAL 6001-4
TRANSMISSION INPUT SHAFT AND DRIVE PLATE INSTALLATION 6001-8
INPUT DROP BOXSECTION 6002
SPECIAL TOOLS 6002-3
SPECIAL TORQUES 6002-3
INPUT DROP BOX 6002-4
DISASSEMBLY 6002-6
ENGINE FRAME AND DROP BOX SPLITSECTION 6003
SPECIAL TORQUES 6003-3
SPECIAL TOOLS 6003-3
ENGINE FRAME AND DROP BOX SPLIT 6003-4
REMOVAL 6003-4
INSTALLATION 6003-6
SPEED TO RANGE TRANSMISSION SPLIT SECTION 6005
SPECIAL TOOLS 6005-3
SPECIAL TORQUES 6005-3
SPEED TO RANGE TRANSMISSION SPLIT 6005-4
REMOVAL 6005-4
INSTALLATION 6005-7
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
5
SPEED TRANSMISSIONSECTION 6006
PICTORIAL INDEX – SPEED TRANSMISSION 6006-3
SPECIFICATIONS 6006-4
SPECIAL TORQUES 6006-4
TROUBLESHOOTING AFTER SPEED TRANSMISSION REPAIR 6006-4
SPECIAL TOOLS 6006-5
SPEED TRANSMISSION WITH CREEP OPTION 6006-6
ASSEMBLING THE COUNTERSHAFT WITH CREEPER SPEED CLUTCH 6006-14
TRANSMISSION ASSEMBLY WITH CREEP OPTION 6006-78
TRANSMISSION ASSEMBLY WITHOUT CREEP OPTION 6006-80
RANGE TRANSMISSION TO REAR FRAME SPLITSECTION 6007
SPECIAL TOOLS 6007-3
SPECIAL TORQUES 6007-3
RANGE TRANSMISSION TO REAR FRAME SPLIT 6007-4
DISASSEMBLY 6007-4
ASSEMBLY 6007-7
RANGE TRANSMISSION SECTION 6008
SPECIFICATIONS 6008-3
TROUBLESHOOTING AFTER RANGE TRANSMISSION REPAIR 6008-3
SPECIAL TORQUES 6008-3
SPECIAL TOOLS 6008-4
RANGE TRANSMISSION 6008-5
Removing the Shaft Master Clutch 6008-5
Removing the Input Shaft, Countershaft and Mechanical Front Drive (MFD) / Park Brake Assembly 6008-7
Disassembly of the Master Clutch 6008-12
Exploded View of the Master Clutch 6008-14
Assembly of the Master Clutch 6008-15
Disassembly of the Range Transmission Input Shaft 6008-16
Exploded View of the Range Transmission Input Shaft 6008-22
Assembly of the Range Transmission Input Shaft 6008-23
Cross-Section of Input Shaft 6008-32
Disassembly of the Range Transmission Countershaft 6008-33
Exploded View of the Range Transmission Countershaft 6008-37
Assembly of the Range Transmission Countershaft 6008-38
Mechanical Front Drive (MFD) – Emergency Brake Disassembly 6008-45
Exploded View of MFD and Emergency Brake 6008-51
Assembly of the MFD / Emergency Brake 6008-52
Exploded View of the Range Transmission Countershaft, Input Shaft, and MFD Input Shaft 6008-66
Installing the Range Transmission Countershaft, Input Shaft,
and MFD Input Shaft into the Range Transmission Housing 6008-67
SETTING THE END PLAY OF THE RANGE TRANSMISSION
COUNTERSHAFT AND INPUT SHAFT 6008-73
Installing the Range Input Master Clutch 6008-75
TRANSMISSION CONTROL VALVES AND INCHING VALVE SECTION 6009
SPECIAL TORQUES 6009-3
POWERSHIFT TRANSMISSION CONTROL VALVES 6009-3
TRANSMISSION CONTROL VALVE CONFIGURATION 6009-4
INCHING VALVE 6009-15
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
6
REAR FRAMESECTION 6011
SPECIFICATIONS 6011-3
SPECIAL TORQUES 6011-3
SPECIAL TOOLS 6011-3
DIFFERENTIAL 6011-4
Removal 6011-4
Disassembly 6011-10
PINION SHAFT 6011-14
Removal and Disassembly 6011-14
Assembly and Installation 6011-16
DIFFERENTIAL ASSEMBLY 6011-24
DIFFERENTIAL INSTALLATION 6011-29
ADJUSTING THE DIFFERENTIAL PRELOAD 6011-35
ADJUSTING THE RING AND PINION BACKLASH 6011-37
BEVEL PINION AND GEAR TOOTH CONTACT CHECK 6011-38
HYDRAULIC PUMP DRIVE SECTION 6012
SPECIAL TORQUES 6012-3
SPECIFICATIONS 6012-3
PUMP DRIVE 6012-3
Removal 6012-3
Disassembly 6012-4
Assembly 6012-7
Installation 6012-12
MECHANICAL FRONT DRIVE (MFD) CONTROL SYSTEM – HOW IT WORKS SECTION 6013
MECHANICAL FRONT DRIVE (MFD) 6013-3
ELECTRONIC MFD CONTROL 6013-5
MFD CONTROL MODES 6013-7
MFD FUNCTIONAL TESTS 6013-8
MFD Valve 6013-9
Solenoid Cartridge Valve 6013-9
TROUBLESHOOTING 6013-10
DIFFERENTIAL LOCK CONTROL SYSTEM – HOW IT WORKSSECTION 6014
ELECTRONIC DIFFERENTIAL LOCK CONTROL 6014-5
DIFFERENTIAL LOCK CONTROL MODES 6014-7
DIFFERENTIAL LOCK CONTROL 6014-8
DIFFERENTIAL LOCK FUNCTIONAL TESTS 6014-9
TROUBLESHOOTING 6014-12
PTO/DIFFERENTIAL LOCK VALVE CIRCUIT 6014-15
MFD OUTPUT SHAFT SECTION 6015
SPECIAL TORQUES 6015-3
MFD OUTPUT SHAFT 6015-4
MFD DRIVE SHAFTSECTION 6016
SPECIAL TORQUES 6016-3
MFD DRIVE SHAFT REMOVAL 6016-4
MFD DRIVE SHAFT INSTALLATION 6016-6
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
7
LIMITED SLIP MFD DIFFERENTIAL SECTION 6017
SPECIFICATIONS 6017-2
SPECIAL TORQUES 6017-2
SPECIAL TOOLS 6017-2
DIFFERENTIAL CARRIER ASSEMBLY REMOVAL 6017-3
DIFFERENTIAL DISASSEMBLY 6017-4
Pinion Disassembly 6017-8
DIFFERENTIAL ASSEMBLY 6017-11
DIFFERENTIAL CARRIER ASSEMBLY 6017-15
Pinion Position and Assembly 6017-15
Shim Pack Thickness Chart 6017-16
Setting The Pinion Depth 6017-17
Adjusting Bearing Preload 6017-20
DIFFERENTIAL INSTALLATION 6017-22
Checking Backlash 6017-23
Ring Gear and Pinion Tooth Pattern Interpretation 6017-25
Installation of Carrier Assembly to Axle Housing 6017-27
LOCKING MFD DIFFERENTIAL SECTION 6018
SPECIFICATIONS 6018-3
SPECIAL TORQUES 6018-3
SPECIAL TOOLS 6018-3
REMOVAL OF THE FRONT DIFFERENTIAL CARRIER ASSEMBLY 6018-4
REMOVAL OF THE FRONT DIFFERENTIAL FROM THE CARRIER HOUSING 6018-5
DISASSEMBLY OF THE DIFFERENTIAL 6018-7
PINION DISASSEMBLY 6018-9
ASSEMBLY OF THE DIFFERENTIAL 6018-12
DIFFERENTIAL CARRIER ASSEMBLY 6018-16
SETTING THE PINION DEPTH 6018-18
ADJUSTING BEARING PRELOAD 6018-21
DIFFERENTIAL INSTALLATION 6018-23
REAR AXLE AND PLANETARIESSECTION 6019
SPECIAL TOOLS 6019-3
SPECIAL TORQUES 6019-5
SPECIFICATIONS 6019-5
GENERAL INFORMATION 6019-5
REAR AXLE 6019-6
AXLE HOUSING DISASSEMBLY 6019-9
PLANETARY DISASSEMBLY 6019-11
DIFFERENTIAL CARRIER SEAL REPLACEMENT 6019-13
PLANETARY ASSEMBLY – THREE PIN 6019-14
PLANETARY ASSEMBLY – FOUR PIN 6019-15
AXLE HOUSING ASSEMBLY 6019-18
HOW TO DETERMINE RAM PRESSURE 6019-23
AXLE INSTALLATION 6019-26
AXLE SEAL WEAR SLEEVE INSTALLATION (4-Inch Axle Only) 6019-30
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
8
POWER TAKE OFF CONTROL SYSTEM – HOW IT WORKS SECTION 6020
POWER TAKE OFF 6020-3
ELECTRONIC PTO CONTROL 6020-4
PTO SYSTEM CONTROL 6020-7
PTO CONTROL MODES 6020-8
PTO VALVE OIL SUPPLY 6020-10
PTO/DIFFERENTIAL LOCK VALVE 6020-11
TROUBLESHOOTING 6020-12
PTO CLUTCH ENGAGED 6020-13
TROUBLESHOOTING 6020-14
MFD PLANETARY HUB, STEERING KNUCKLE AND DRIVE SHAFTSECTION 6022
SPECIFICATIONS 6022-3
SPECIAL TORQUES 6022-3
SPECIAL TOOLS 6022-3
PLANETARY HUB DISASSEMBLY 6022-4
STEERING KNUCKLE AND KINGPIN DISASSEMBLY 6022-9
AXLE DRIVE SHAFT DISASSEMBLY 6022-13
AXLE SHAFT ASSEMBLY 6022-14
KINGPIN ASSEMBLY 6022-16
STEERING KNUCKLE ASSEMBLY 6022-20
PLANETARY HUB ASSEMBLY 6022-24
Ten Bolt Axle Only 6022-29
Twelve Bolt Axle Only 6022-33
All Axles 6022-38
SUSPENSION MFD AXLESECTION 6023
SPECIAL TORQUES 6023-2
SUSPENSION MFD AXLE 6023-3
Disassembly 6023-3
Assembly 6023-13
Position Sensor Adjustment 6023-25
SUSPENSION MFD AXLE SYSTEM – HOW IT WORKS AND TROUBLESHOOTINGSECTION 6024
SUSPENDED MFD AXLE OPERATION 6024-3
SUSPENDED MFD AXLE- CALIBRATION MODE 6024-9
ERROR TABLE 6024-11
SUSPENDED MFD AXLE- MANUAL OPERATION MODE (TEST MODE) 6024-13
SUSPENDED MFD AXLE- DEMONSTRATION MODE 6024-16
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
9
PTO CLUTCH ASSEMBLY SINGLE, REVERSIBLE AND DUAL SPEEDSECTION 6025
SPECIAL TOOLS 6025-3
SPECIAL TORQUES 6025-3
PTO CLUTCH ASSEMBLY 6025-4
General 6025-4
PTO CLUTCH SERVICE 6025-4
Removal 6025-4
Disassembly 6025-6
Assembly 6025-16
Exploded View of PTO Clutch 6025-16
Cross Section of PTO Clutch and Output Shaft Assembly 6025-31
SINGLE SPEED REVERSIBLE SHAFT PTO 6025-32
Disassembly 6025-32
Assembly 6025-35
Exploded View of PTO Output Shaft and Driven Gear Assembly 6025-35
SINGLE SPEED REVERSIBLE SHAFT PTO DRIVEN GEAR 6025-39
Removal 6025-39
Assembly 6025-41
Reversible PTO Output Shaft Bearing Adjustment 6025-43
SINGLE SPEED REVERSIBLE SHAFT PTO 6025-45
Cross Section of PTO Output Shaft Assembly 6025-45
BRAKE VALVESECTION 7001
SPECIAL TORQUES 7001-2
BRAKE VALVE 7001-3
Removal 7001-3
Disassembly 7001-4
Assembly 7001-6
Installation 7001-8
BRAKE CYLINDERSSECTION 7002
SPECIAL TORQUES 7002-3
SPECIFICATIONS 7002-3
BRAKE CYLINDERS 7002-3
Disassembly 7002-3
Assembly 7002-5
HYDRAULIC SCHEMATIC – EUROPEAN 87518876
HOW TO READ SYMBOLS IN A HYDRAULIC SCHEMATIC SECTION 8000
SIMPLE SCHEMATIC 8000-13
COMMON SYMBOLS 8000-15
PTO AND DIFFERENTIAL LOCK VALVESECTION 8001
SPECIAL TORQUES 8002-2
SPECIFICATIONS 8002-2
PTO AND DIFFERENTIAL LOCK VALVE 8002-3
PTO AND DIFFERENTIAL LOCK VALVESECTION 8002
SPECIAL TORQUES 8002-2
SPECIFICATIONS 8002-2
PTO AND DIFFERENTIAL LOCK VALVE 8002-3
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
10
REMOTE VALVE AND COUPLER SERVICESECTION 8003
SPECIAL TORQUES 8003-2
REMOTE VALVE AND COUPLER SERVICE 8003-3
REMOTE VALVE REMOVAL AND SERVICE 8003-5
REMOTE COUPLERS 8003-13
REMOTE HYDRAULIC SYSTEM – HOW IT WORKS AND TROUBLESHOOTINGSECTION 8004
REMOTE HYDRAULIC SYSTEM INTRODUCTION 8004-3
REMOTE VALVE SYSTEM COMPONENTS 8004-5
REMOTE VALVE SYSTEM CONTROLS 8004-10
REMOTE VALVE OPERATION 8004-14
REMOTE VALVE PROBLEMS AND WHERE TO LOOK 8004-23
REMOTE VALVE PROPORTIONAL CURRENT CONTROL (PCC) SOLENOID OPERATION 8004-25
REMOTE VALVE SYSTEM TESTING 8004-26
REMOTE VALVE HIGH PRESSURE TEST 8004-27
PFC PUMP HIGH PRESSURE STANDBY CHECK AND ADJUSTMENT PROCEDURE 8004-28
PFC PISTON PUMP FLOW TEST 8004-29
STANDARD PUMP COMPENSATOR VALVE INSPECTION 8004-30
REMOTE VALVE SIGNAL CHECK AND HITCH SIGNAL CHECK 8004-31
REMOTE VALVE COUPLER TEST 8004-32
LOAD CHECK INSPECTION 8004-33
OPERATIONAL PROBLEMS 8004-34
PRIORITY AND REGULATOR VALVESECTION 8005
SPECIAL TORQUES 8005-3
PRIORITY VALVE AND REGULATOR 8005-4
Removal 8005-4
Disassembly 8005-6
Assembly 8005-9
Installation 8005-12
CROSS SECTION OF PRIORITY AND REGULATOR VALVE 8005-14
CHARGE PUMPSECTION 8006
CHARGE PUMP 8006-3
Removal 8006-3
Installation 8006-4
PFC PISTON PUMP AND HYDRAULIC FILTERSECTION 8007
SPECIAL TORQUES 8007-3
PFC PISTON PUMP 8007-3
Removal 8007-3
Installation 8007-4
HITCH SYSTEM – HOW IT WORKSSECTION 8008
THREE POINT HITCH 8008-3
ELECTRONIC HITCH CONTROL 8008-4
ELECTRONIC HITCH CONTROL SYSTEM FEATURES 8008-7
HITCH CONTROL VALVE 8008-14
HITCH CONTROL VALVE 8008-16
SETUP / ADJUSTMENT SEQUENCE 8008-22
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
11
HITCH CONTROL VALVE SECTION 8009
HITCH CONTROL VALVE 8009-3
Removal 8009-3
Disassembly 8009-5
Assembly 8009-7
Installation 8009-9
HITCH CONTROL VALVE CROSS SECTION 8009-11
TRACTOR HITCH SECTION 8010
SPECIAL TORQUES 8010-3
TRACTOR HITCH 8010-3
EDC PIN ASSEMBLY 8010-20
POTENTIOMETER (HITCH POSITION SENSOR) 8010-21
CAM SWAY LIMITER 8010-23
CAM BUMPERS FOR DRAFT ARM 8010-25
DRAWBAR, HIGH VERTICAL CAPACITY 8010-26
PEDAL AND PEDAL SWITCH ADJUSTMENTSSECTION 9001
INCHING PEDAL SWITCH ADJUSTMENT 9001-3
BRAKE PEDAL ADJUSTMENTS 9001-4
CAB RAISE / REMOVAL AND INSTALLATIONSECTION 9005
SPECIAL TORQUES 9005-3
SPECIAL TOOLS 9005-3
CAB RAISE PROCEDURE 9005-4
CAB LOWERING PROCEDURE 9005-7
CAB REMOVAL 9005-10
CAB INSTALLATION 9005-17
HOOD REMOVAL SECTION 9008
HOOD 9008-3
Hood Removal 9008-3
Hood Installation 9008-4
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
12
AIR CONDITIONING SYSTEM – TROUBLESHOOTING AND FAULT CODESSECTION 9010
SAFETY PROCEDURES 9010-5
SPECIAL TOOLS 9010-6
A/C THERMAL OPERATION 9010-7
A/C SYSTEM COMPONENTS 9010-9
Cab HVAC Box Components – Automatic Temperature Control 9010-9
Chassis Components 9010-11
AUTOMATIC TEMPERATURE CONTROL (ATC) OPERATION 9010-12
Operation Modes 9010-15
Automatic Mode 9010-15
Defog Mode 9010-15
Automatic Operation Summary 9010-16
Defog/Dehumidify Operation Summary 9010-17
ATC FAULT CODES 9010-18
ATC Fault Code 111 9010-18
ATC Fault Code 112 9010-19
ATC Fault Code 115 9010-19
ATC Fault Code 116 9010-20
ATC Fault Code 120 9010-20
ATC Fault Code 121 9010-21
ATC Fault Code 122 9010-21
ATC Fault Code 125 9010-22
ATC Fault Code 126 9010-22
ATC Fault Code 127 9010-23
ATC Fault Code 128 9010-23
ATC Fault Code 129 9010-24
ATC Fault Code 130 9010-24
ATC Fault Code 131 9010-25
ATC Fault Code 132 9010-25
ATC Fault Code 133 9010-26
ATC Fault Code 134 9010-26
LOCATING SYSTEM PROBLEMS WITHOUT FAULT CODES 9010-27
Controller-Based Resistance Tests 9010-27
ATC CONTROLLER TEST (CONNECTOR J8 TEST POINTS) 9010-29
ATC Field Reported Symptoms/Causes 9010-32
COMPRESSOR AND CLUTCH 9010-33
Operational Check 9010-33
Electrical Test 9010-36
Compressor Clutch Control Circuit Test Procedure 9010-36
Service Note: Adjusting Clutch Air Gap 9010-38
HIGH AND LOW PRESSURE SWITCH CLUTCH LATCHING CIRCUIT 9010-39
Background 9010-39
Possible Failure Modes – Fault Codes 129 and 134 9010-40
Electrical Test 9010-41
High Pressure Switch and Circuit Test 9010-41
Low Pressure Switch and Circuit Test 9010-42
HEATER CONTROL VALVE 9010-43
Operational Check 9010-43
Electrical Test 9010-44
Heater Control Valve Power, Signal and Ground Test 9010-44
BLOWER SPEED AND TEMPERATURE CONTROL POTENTIOMETERS 9010-45
Background 9010-45
Possible Failure Modes – Fault Codes 120, 121 9010-45
Electrical Test 9010-46
Common Control Potentiometer and Circuit Test Procedure 9010-46
BLOWER AND BLOWER SPEED DRIVER 9010-47
Background 9010-47
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
13
Power, Signal and Ground Circuit 9010-47
Possible Failure Modes 9010-47
Blower Motor/Blower Driver Power, Signal and Ground Test 9010-48
CAB AND EVAPORATOR TEMPERATURE SENSORS 9010-49
Background 9010-49
Electrical Test 9010-51
Power Circuit 9010-51
Possible Failure Modes – Fault Codes 111, 115 and 116 9010-52
Cab Temperature Sensor and Circuit Test 9010-53
Evaporator Temperature Sensor and Circuit Test 9010-54
CONTROLLER POWER, GROUND, AND ATC SWITCH 9010-56
Background 9010-56
Power and Ground Circuit 9010-56
Possible Failure Modes 9010-56
Controller Power Supply and Ground Test 9010-56
ATC Switch and Circuit Test 9010-57
Defog/Defrost Switch and Circuit Test 9010-57
CAB PRESSURIZER BLOWER 9010-58
Background 9010-58
Power and Ground 9010-58
Cab Pressurizer Blower & Relay Power Supply and Ground Test 9010-58
ACCESSING THE HVAC BOX 9010-59
STANDARD AIR CONDITIONING (STD) TROUBLESHOOTING 9010-60
Standard A/C Operation 9010-61
Smart Pressure Switch Cycling System 9010-61
Standard A/C Controls and Their Function 9010-62
Symptom-Based Standard A/C Troubleshooting 9010-63
Controller Power, Ground And A/C Switch 9010-65
Background 9010-65
Power and Ground Circuit 9010-65
Possible Failure Modes 9010-65
Controller Power Supply and Ground Test 9010-65
A/C Switch and Circuit Test 9010-66
Compressor And Clutch 9010-67
Operational Check 9010-67
Electrical Test – Compressor Clutch 9010-70
Clutch Relay Power Supply and Ground Test 9010-71
Service Note: Adjusting Clutch Air Gap 9010-72
High And Low Pressure Switch Clutch Latching Circuit 9010-73
Background 9010-73
Possible Failure Modes – Flashing Pressure Warning Lamp 9010-74
Electrical Test – Pressure Switches 9010-75
High Pressure Switch and Circuit Test 9010-75
Low Pressure Switch and Circuit Test 9010-76
Heater Control Valve 9010-77
Operational Check 9010-77
Electrical Test 9010-78
Temperature Control Potentiometer 9010-79
Background 9010-79
Electrical Test 9010-79
Blower Speed Switch And Blower Motor 9010-80
Background 9010-80
Power and Ground Circuit 9010-80
Possible Failure Modes 9010-80
Blower Speed Switch and Power Circuit Test 9010-81
Blower Motor Power, and Control Circuit Test 9010-81
Evaporator Temperature Sensor 9010-83
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
14
Background 9010-83
Electrical Test – Sensor 9010-83
Power Circuit 9010-84
Service Note: Too Little Cooling/Too Much Heating without Symptoms 9010-84
Evaporator Temperature Sensor and Circuit Test 9010-84
Controller Power, Ground And A/C Switch 9010-86
Background 9010-86
Power and Ground Circuit 9010-86
Possible Failure Modes 9010-86
Controller Power Supply and Ground Test 9010-86
A/C Switch and Circuit Test 9010-87
Cab Pressurizer Blower 9010-88
Background 9010-88
Power and Ground 9010-88
Cab Pressurizer Blower & Relay Power Supply and Ground Test 9010-89
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
15
AIR CONDITIONER SYSTEM SERVICESECTION 9020
SPECIFICATIONS 9020-4
SPECIAL TORQUES 9020-4
SPECIAL TOOLS 9020-4
SAFETY PROCEDURES 9020-9
AIR CONDITIONER SYSTEM REFRIGERANT RECOVERY 9020-10
RECOVERING PURE 134A REFRIGERANT 9020-12
RECOVERING CONTAMINATED REFRIGERANT WITH OEM1691 9020-16
Preparing the Tank 9020-16
Recovery Process 9020-20
AIR CONDITIONER SYSTEM EVACUATION AND RECHARGING 9020-26
AIR CONDITIONING TEMPERATURE/PRESSURE CHART 9020-33
LEAK DETECTION 9020-34
Electronic Testing with OEM1437 9020-35
Florescent Leak Detection 9020-36
Fluorescent Dye Injection 9020-36
Fluorescent Leak Testing 9020-42
A/C SYSTEM FLUSHING PROCEDURE 9020-43
Required Tools 9020-44
Precautions 9020-45
Component Flushing Procedure with Power Flush 17550 9020-46
Complete Circuit Flushing Procedure with Power Flush 17550 9020-50
Back Flushing the Thermal Expansion Valve or Refrigerant Line 9020-55
Post Flushing Procedures 9020-57
Flushing Solvent Disposal 9020-59
A/C SYSTEM COMPONENTS 9020-60
Cab HVAC Box Components – Automatic Temperature Control 9020-60
Cab HVAC Components – Standard Systems 9020-62
Chassis Components 9020-64
A/C COMPRESSOR CLUTCH 9020-65
Clutch Removal 9020-65
Exploded View of Clutch 9020-71
Compressor Clutch Replacement 9020-71
A/C COMPRESSOR 9020-79
Oil Level Check or Adjustment 9020-79
Compressor Removal 9020-82
Compressor Installation 9020-85
CONDENSER AND RECEIVER-DRIER 9020-87
Condenser 9020-87
Receiver-Drier 9020-89
ACCESSING THE HVAC BOX 9020-90
THERMAL EXPANSION VALVE TESTING 9020-92
THERMAL EXPANSION VALVE REPLACEMENT 9020-93
EVAPORATOR AND CAB TEMPERATURE SENSOR LOCATION 9020-95
BLOWER MOTOR REPLACEMENT 9020-96
HEATER CONTROL VALVE REPLACEMENT 9020-97
EVAPORATOR/HEATER ASSEMBLY 9020-98
Evaporator/Heater Assembly Removal 9020-98
Evaporator/Heater Assembly Installation 9020-101
Post Replacement Procedures 9020-104
EVAPORATOR/HEATER ASSEMBLY SEALING AND CLEANING 9020-105
BLOWER AND EVAPORATOR REFERENCE ILLUSTRATION 9020-106
CONTROLLER AND BLOWER SPEED DRIVER REPLACEMENT 9020-107
ATC Controller 9020-107
Standard A/C Controller 9020-107
Blower Speed Driver (ATC Units Only) 9020-108
CAB AIR FILTER SERVICE 9020-109
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
16
CAB RECIRCULATION AIR FILTER SERVICE 9020-110
CAB PRESSURIZATION TEST 9020-111
CAB PRESSURIZER MOTOR REPLACEMENT 9020-113
VISCOUS FAN DRIVE 9020-116
INSTRUMENTATION CONTROLLER FAULT CODES SECTION 10001
FAULT CODE INST 1015 10001-10
FAULT CODE INST 3010 10001-12
FAULT CODE INST 3020 10001-13
FAULT CODE INST 3022 10001-13
FAULT CODE INST 5010 10001-13
FAULT CODE INST 5011 10001-14
FAULT CODE INST 10031 10001-15
FAULT CODE INST 10032 10001-15
FAULT CODE INST 10033 10001-15
FAULT CODE INST 10034 10001-16
FAULT CODE INST 10035 10001-16
FAULT CODE INST 10036 10001-16
FAULT CODE INST 10037 10001-17
FAULT CODE INST 10038 10001-17
FAULT CODE INST 11011 10001-18
FAULT CODE INST 12011 10001-19
FAULT CODE INST 12043 10001-21
FAULT CODE INST 12051 10001-23
FAULT CODE INST 12071 10001-25
FAULT CODE INST 12091 10001-27
FAULT CODE INST 12111 10001-29
FAULT CODE INST 13010 10001-31
FAULT CODE INST 13011 10001-32
FAULT CODE INST 13012 10001-33
FAULT CODE INST 13021 10001-34
FAULT CODE INST 13022 10001-35
FAULT CODE INST 13040 10001-36
FAULT CODE INST 13051 10001-37
FAULT CODE INST 13052 10001-38
FAULT CODE INST 53001 10001-39
FAULT CODE INST 53005 10001-39
FAULT CODE INST 65535 10001-39
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
17
AUX / HITCH / PTO FAULT CODES – TRACTOR MULTI FUNCTION (TMF) CONTROLLER SECTION 10002
AUX/HITCH/PTO FAULT CODE 2 10002-7
AUX/HITCH/PTO FAULT CODE 4 10002-8
AUX/HITCH/PTO FAULT CODE 5 10002-9
AUX/HITCH/PTO FAULT CODE 7 10002-10
AUX/HITCH/PTO FAULT CODE 11 10002-11
AUX/HITCH/PTO FAULT CODE 12 10002-13
AUX/HITCH/PTO FAULT CODE 14 10002-14
AUX/HITCH/PTO FAULT CODE 15 10002-15
AUX/HITCH/PTO FAULT CODE 17 10002-16
AUX/HITCH/PTO FAULT CODE 18 10002-17
AUX/HITCH/PTO FAULT CODE 19 10002-18
AUX/HITCH/PTO FAULT CODE 21 10002-18
AUX/HITCH/PTO FAULT CODE 22 10002-19
AUX/HITCH/PTO FAULT CODE 23 10002-20
AUX/HITCH/PTO FAULT CODE 24 10002-21
AUX/HITCH/PTO FAULT CODE 25 10002-22
AUX/HITCH/PTO FAULT CODE 26 10002-23
AUX/HITCH/PTO FAULT CODE 28 10002-24
AUX/HITCH/PTO FAULT CODE 29 10002-24
AUX/HITCH/PTO FAULT CODE 30 10002-25
AUX/HITCH/PTO FAULT CODE 31 10002-26
AUX/HITCH/PTO FAULT CODE 32 10002-28
AUX/HITCH/PTO FAULT CODE 33 10002-29
AUX/HITCH/PTO FAULT CODE 34 10002-29
AUX/HITCH/PTO FAULT CODE 35 10002-30
AUX/HITCH/PTO FAULT CODE 37 10002-31
AUX/HITCH/PTO FAULT CODE 41 10002-31
AUX/HITCH/PTO FAULT CODE 42 10002-32
AUX/HITCH/PTO FAULT CODE 43 10002-32
AUX/HITCH/PTO FAULT CODE 44 10002-32
AUX/HITCH/PTO FAULT CODE 45 10002-32
AUX/HITCH/PTO FAULT CODE 47 10002-33
AUX/HITCH/PTO FAULT CODE 48 10002-33
AUX/HITCH/PTO FAULT CODE 50 10002-34
AUX/HITCH/PTO FAULT CODE 51 10002-34
AUX/HITCH/PTO FAULT CODE 52 10002-35
AUX/HITCH/PTO FAULT CODE 53 10002-35
AUX/HITCH/PTO FAULT CODE 54 10002-36
AUX/HITCH/PTO FAULT CODE 55 10002-37
AUX/HITCH/PTO FAULT CODE 56 10002-38
AUX/HITCH/PTO FAULT CODE 57 10002-39
AUX/HITCH/PTO FAULT CODE 58 10002-40
AUX/HITCH/PTO FAULT CODE 59 10002-41
AUX/HITCH/PTO FAULT CODE 60 10002-41
AUX/HITCH/PTO FAULT CODE 61 10002-42
AUX/HITCH/PTO FAULT CODE 62 10002-42
AUX/HITCH/PTO FAULT CODE 63 10002-42
AUX/HITCH/PTO FAULT CODE 64 10002-43
AUX/HITCH/PTO FAULT CODE 65 10002-43
AUX/HITCH/PTO FAULT CODE 66 10002-44
AUX/HITCH/PTO FAULT CODE 80 10002-44
AUX/HITCH/PTO FAULT CODE 81 10002-45
AUX/HITCH/PTO FAULT CODE 82 10002-46
AUX/HITCH/PTO FAULT CODE 83 10002-47
AUX/HITCH/PTO FAULT CODE 86 10002-48
AUX/HITCH/PTO FAULT CODE 87 10002-49
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
18
AUX/HITCH/PTO FAULT CODE 88 10002-50
AUX/HITCH/PTO FAULT CODE 89 10002-50
AUX/HITCH/PTO FAULT CODE 90 10002-51
AUX/HITCH/PTO FAULT CODE 92 10002-51
AUX/HITCH/PTO FAULT CODE 93 10002-52
AUX/HITCH/PTO FAULT CODE 94 10002-52
AUX/HITCH/PTO FAULT CODE 98 10002-53
AUX/HITCH/PTO FAULT CODE 99 10002-53
AUX/HITCH/PTO FAULT CODE 106 10002-54
AUX/HITCH/PTO FAULT CODE 107 10002-54
AUX/HITCH/PTO FAULT CODE 108 10002-55
AUX/HITCH/PTO FAULT CODE 109 10002-55
AUX/HITCH/PTO FAULT CODE 110 10002-56
AUX/HITCH/PTO FAULT CODE 111 10002-56
AUX/HITCH/PTO FAULT CODE 112 10002-57
AUX/HITCH/PTO FAULT CODE 113 10002-58
AUX/HITCH/PTO FAULT CODE 114 10002-59
AUX/HITCH/PTO FAULT CODE 115 10002-60
AUX/HITCH/PTO FAULT CODE 116 10002-61
AUX/HITCH/PTO FAULT CODE 120 10002-62
AUX/HITCH/PTO FAULT CODE 123 10002-62
AUX/HITCH/PTO FAULT CODE 124 10002-63
AUX/HITCH/PTO FAULT CODE 125 10002-64
AUX/HITCH/PTO FAULT CODE 126 10002-65
AUX/HITCH/PTO FAULT CODE 127 10002-66
AUX/HITCH/PTO FAULT CODE 128 10002-67
AUX/HITCH/PTO FAULT CODE 129 10002-68
AUX/HITCH/PTO FAULT CODE 130 10002-69
AUX/HITCH/PTO FAULT CODE 131 10002-70
AUX/HITCH/PTO FAULT CODE 132 10002-71
AUX/HITCH/PTO FAULT CODE 133 10002-72
AUX/HITCH/PTO FAULT CODE 134 10002-73
AUX/HITCH/PTO FAULT CODE 135 10002-74
AUX/HITCH/PTO FAULT CODE 136 10002-75
AUX/HITCH/PTO FAULT CODE 137 10002-76
AUX/HITCH/PTO FAULT CODE 138 10002-77
AUX/HITCH/PTO FAULT CODE 139 10002-78
AUX/HITCH/PTO FAULT CODE 140 10002-79
AUX/HITCH/PTO FAULT CODE 141 10002-80
AUX/HITCH/PTO FAULT CODE 142 10002-81
AUX/HITCH/PTO FAULT CODE 147 10002-82
AUX/HITCH/PTO FAULT CODE 148 10002-82
AUX/HITCH/PTO FAULT CODE 149 10002-83
AUX/HITCH/PTO FAULT CODE 150 10002-83
AUX/HITCH/PTO FAULT CODE 151 10002-84
AUX/HITCH/PTO FAULT CODE 152 10002-86
AUX/HITCH/PTO FAULT CODE 153 10002-86
AUX/HITCH/PTO FAULT CODE 154 10002-87
AUX/HITCH/PTO FAULT CODE 155 10002-87
AUX/HITCH/PTO FAULT CODE 156 10002-88
AUX/HITCH/PTO FAULT CODE 157 10002-88
AUX/HITCH/PTO FAULT CODE 158 10002-89
AUX/HITCH/PTO FAULT CODE 159 10002-89
AUX/HITCH/PTO FAULT CODE 160 10002-90
AUX/HITCH/PTO FAULT CODE 161 10002-91
AUX/HITCH/PTO FAULT CODE 162 10002-92
AUX/HITCH/PTO FAULT CODE 163 10002-93
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
19
AUX/HITCH/PTO FAULT CODE 164 10002-94
AUX/HITCH/PTO FAULT CODE 165 10002-95
AUX/HITCH/PTO FAULT CODE 166 10002-96
AUX/HITCH/PTO FAULT CODE 167 10002-97
AUX/HITCH/PTO FAULT CODE 168 10002-98
AUX/HITCH/PTO FAULT CODE 169 10002-99
AUX/HITCH/PTO FAULT CODE 170 10002-100
AUX/HITCH/PTO FAULT CODE 171 10002-101
AUX/HITCH/PTO FAULT CODE 172 10002-101
AUX/HITCH/PTO FAULT CODE 173 10002-102
AUX/HITCH/PTO FAULT CODE 174 10002-103
AUX/HITCH/PTO FAULT CODE 175 10002-104
AUX/HITCH/PTO FAULT CODE 178 10002-106
AUX/HITCH/PTO FAULT CODE 179 10002-107
AUX/HITCH/PTO FAULT CODE 180 10002-108
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
20
TRANSMISSION CONTROLLER FAULT CODES (INCLUDES SUSPENDED AXLE) SECTION 10003
FAULT CODE TRANS 11 10003-5
FAULT CODE TRANS 12 10003-6
FAULT CODE TRANS 24 10003-7
FAULT CODE TRANS 37 10003-8
FAULT CODE TRANS 10003-9
FAULT CODE TRANS 47 10003-10
FAULT CODE TRANS 48 10003-12
FAULT CODE TRANS 49 10003-13
FAULT COE TRANS 50 10003-14
FAULT CODE TRANS 51 10003-15
FAULT CODE TRANS 52 10003-16
FAULT CODE TRANS 53 10003-17
FAULT CODE TRANS 54 10003-19
FAULT CODE TRANS 59 10003-21
FAULT CODE TRANS 60 10003-22
FAULT CODE TRANS 66 10003-23
FAULT CODE TRANS 67 10003-24
FAULT CODE TRANS 68 10003-25
FAULT CODE TRANS 69 10003-26
FAULT CODE TRANS 70 10003-27
FAULT CODE TRANS 72 10003-27
FAULT CODE TRANS 73 10003-28
FAULT CODE TRANS 74 10003-28
FAULT CODE TRANS 77 10003-29
FAULT CODE TRANS 78 10003-30
FAULT CODE TRANS 79 10003-31
FAULT CODE TRANS 80 10003-32
FAULT CODE TRANS 81 10003-34
FAULT CODE TRANS 82 10003-36
FAULT CODE TRANS 83 10003-36
FAULT CODE TRANS 103 10003-37
FAULT CODE TRANS 104 10003-38
FAULT CODE TRANS 105 10003-39
FAULT CODE TRANS 106 10003-40
FAULT CODE TRANS 107 10003-41
FAULT CODE TRANS 108 10003-42
FAULT CODE TRANS 109 10003-43
FAULT CODE TRANS 110 10003-44
FAULT CODE TRANS 111 10003-45
FAULT CODE TRANS 112 10003-46
FAULT CODE TRANS 113 10003-47
FAULT CODE TRANS 114 10003-48
FAULT CODE TRANS 115 10003-49
FAULT CODE TRANS 116 10003-50
FAULT CODE TRANS 117 10003-51
FAULT CODE TRANS 118 10003-52
FAULT CODE TRANS 119 10003-53
FAULT CODE TRANS 120 10003-54
FAULT CODE TRANS 121 10003-55
FAULT CODE TRANS 122 10003-56
FAULT CODE TRANS 123 10003-57
FAULT CODE TRANS 124 10003-58
FAULT CODE TRANS 125 10003-59
FAULT CODE TRANS 126 10003-59
FAULT CODE TRANS 127 10003-59
FAULT CODE TRANS 128 10003-60
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
21
FAULT CODE TRANS 129 10003-60
FAULT CODE TRANS 130 10003-60
FAULT CODE TRANS 131 10003-61
FAULT CODE TRANS 132 10003-61
FAULT CODE TRANS 133 10003-61
FAULT CODE TRANS 134 10003-62
FAULT CODE TRANS 135 10003-63
FAULT CODE TRANS 136 10003-65
FAULT CODE TRANS 137 10003-67
FAULT CODE TRANS 138 10003-68
FAULT CODE TRANS 139 10003-69
FAULT CODE TRANS 140 10003-70
FAULT CODE TRANS 141 10003-71
FAULT CODE TRANS 142 10003-72
FAULT CODE TRANS 143 10003-72
FAULT CODE TRANS 144 10003-73
FAULT CODE TRANS 145 10003-74
FAULT CODE TRANS 147 10003-75
FAULT CODE TRANS 148 10003-77
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
22
ARM REST CONTROLLER FAULT CODES SECTION 10004
FAULT CODE ARM 19 10004-4
FAULT CODE ARM 29 10004-5
FAULT CODE ARM 39 10004-6
FAULT CODE ARM 49 10004-7
FAULT CODE ARM 59 10004-8
FAULT CODE ARM 69 10004-9
FAULT CODE ARM 79 10004-10
FAULT CODE ARM 89 10004-11
FAULT CODE ARM 99 10004-12
FAULT CODE ARM 109 10004-13
FAULT CODE ARM 119 10004-14
FAULT CODE ARM 129 10004-15
FAULT CODE ARM 139 10004-16
FAULT CODE ARM 149 10004-17
FAULT CODE ARM 159 10004-18
FAULT CODE ARM 169 10004-19
FAULT CODE ARM 1029 10004-20
FAULT CODE ARM 1039 10004-21
FAULT CODE ARM 1049 10004-22
FAULT CODE ARM 1059 10004-23
FAULT CODE ARM 1069 10004-24
FAULT CODE ARM 1079 10004-25
FAULT CODE ARM 1089 10004-26
FAULT CODE ARM 1099 10004-27
FAULT CODE ARM 1109 10004-28
FAULT CODE ARM 1119 10004-29
FAULT CODE ARM 1129 10004-30
FAULT CODE ARM 8011 10004-30
FAULT CODE ARM 9011 10004-31
FAULT CODE ARM 9012 10004-31
FAULT CODE ARM 9013 10004-32
FAULT CODE ARM 9014 10004-32
FAULT CODE ARM 9015 10004-33
FAULT CODE ARM 9021 10004-33
FAULT CODE ARM 9031 10004-34
FAULT CODE ARM 9041 10004-34
FAULT CODE ARM 10091 10004-35
FAULT CODE ARM 12013 10004-36
FAULT CODE ARM 12081 10004-38
FAULT CODE ARM 65535 10004-39
MAGNUM 225/250/280/310 MASTER TABLE OF CONTENTS
23
ELECTRONIC CONTROLLER CONFIGURATION, CALIBRATION
AND FAULT CODE RETRIEVAL SECTION 10005
FAULT CODE RETRIEVAL 10005-3
INSTRUMENTATION PROGRAMMING 10005-5
Radar Calibration 10005-9
Controller Configuration 10005-12
INSTRUMENTATION DISPLAY SYMPTOM BASED FAULTS 10005-17
ARMREST CONTROLLER CONFIGURATION AND CALIBRATION 10005-19
TRANSMISSION CONTROLLER CONFIGURATION AND CALIBRATION 10005-28
When Calibration is Required 10005-28
Clutch Calibration Procedure 10005-39
Calibration Error Messages 10005-43
Front Suspension Calibration 10005-48
REMOTE (AUX) SYSTEM CALIBRATION 10005-55
Aux Cal Menu 10005-61
HITCH SYSTEM CALIBRATION 10005-64
PTO SYSTEM CONFIGURATION 10005-74
Section
1000
1000

PLEASE NOTE:

•  This is the SAME exact manual used by your dealers to fix your vehicle.
• The same can be yours in the next 2-3 mins as you will be directed to the download page
• immediately after paying for the manual.
• Any queries / doubts regarding your purchase, please feel free to contact [email protected]