Case IH Tractor Farmall 40,45,50 With Cab & CVT Transmission Compact Operator’s Manual
VIDEO PREVIEW OF THE MANUAL:
IMAGES PREVIEW OF THE MANUAL:
DESCRIPTION:
Case IH Tractor Farmall 40,45,50 With Cab & CVT Transmission Compact Operator’s Manual
Manual Covered:
Case IH Farmall 40 , Farmall 45, Farmall 50 With Cab and CVT Transmission Compact Tractor
- This manual contains information concerning the adjustment and maintenance of your new equipment. You have purchased a dependable machine, but only by proper care and operation can you expect to receive the performance and long service built into this equipment. Please have all operators read this manual carefully and keep it available for ready reference. Your CASE IH AGRICULTURE dealer will instruct you in the general operation of your new equipment. (Refer to the ‘Delivery Report’ at the back of this manual.)
- Your dealer’s staff of factory-trained service technicians will be glad to answer any questions that may arise regarding the operation of your machine. Case IH Max Service is also available. Call 1-877-4CASEIH (1-877-422-7344) or email [email protected]. Your CASE IH AGRICULTURE dealer carries a complete line of genuine CASE IH AGRICULTURE service parts. These parts are manufactured and carefully inspected to insure high quality and accurate fitting of any necessary replacement parts.
- Be prepared to give your dealer the model and product identification number of your new equipment when ordering parts. Locate these numbers now and record them below. Refer to the ‘General Information’ section of this manual for the location of the model and product identification numbers of your machine.
TABLE OF CONTENTS:
Case IH Tractor Farmall 40,45,50 With Cab & CVT Transmission Compact Operator’s Manual
1 GENERAL INFORMATION
Note to the Owner 1-1
Foreword Ecology and the Environment 1-2
General specification – Biodiesel Fuels 1-3
Advice 1-4
Torque – Minimum Tightening Torques for Normal Assembly 1-5
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS – Torque – Standard
torque data for hydraulics 1-8
Diesel fuel 1-10
Machine orientation1-11
Product Identification Number (PIN) 1-11
Electro-Magnetic Compatibility (EMC) 1-12
2 SAFETY INFORMATION
Precautionary statements and signal word definitions 2-1
Safety rules 2-2
Starting the tractor 2-3
Using the tractor 2-3
Towing and transport2-5
Using implements and agricultural machinery 2-5
Stopping the tractor 2-6
Servicing the tractor 2-6
Proposition 65 2-8
Personal safety2-9
Safety rules2-10
ROPS – Personal safety – Roll-over protective structure 2-12
ENVIRONMENT CONTROL Heating, ventilation and air-conditioning – Personal safety 2-13
Safety signs 2-14
Instructional decals 2-22
International symbols 2-26
3 CONTROLS/INSTRUMENTS
ACCESS TO OPERATOR’S PLATFORM
Doors3-1
OPERATOR’S SEAT
USER CONTROLS AND SEAT Operator seat – Adjust3-1
Seat belt – Adjust3-2
FORWARD CONTROLS
Steering wheel – Adjust3-3
Instrument panel3-4
ADIC programming3-9
ADIC fault codes – Transmission related 3-23
Hand throttle lever 3-25
Front window wiper/washer3-26
Windscreen washer reservoir 3-27
LEFT-HAND SIDE CONTROLS
Transmission shuttle shift lever 3-28
CVT transmission controls 3-28
2WD-4WD SYSTEM – Control3-31
Differential control 3-32
RIGHT-HAND SIDE CONTROLS
Throttle command Pedal – Control identification3-33
Fuel shut-off – Control3-33
PTO controls3-34
Hydraulic power lift (HPL) 3-37
Rear remote control valve(s) 3-37
Front remote control valve 3-37
REARWARD CONTROLS
Rear window3-38
Auxiliary power outlet (if equipped) 3-38
Rear window wiper/washer 3-39
OVERHEAD CONTROLS
ENVIRONMENT CONTROL – Overview 3-40
ENVIRONMENT CONTROL Heating, ventilation and air-conditioning – Adjust 3-41
Cab air filters3-45
Sun shades 3-46
Cab internal lighting 3-46
EXTERIOR CONTROLS
Hood latch3-47
Mirror Rear view mirror – Adjust 3-47
4 OPERATING INSTRUCTIONS
COMMISSIONING THE UNIT
CVT transmission controls – Settings and adjustments4-1
Recommended operating mode settings 4-12
PTO operation 4-14
Extendable drawbar 4-15
Deluxe three-point linkage 4-16
STARTING THE UNIT
Start control Start switch – Control identification4-17
Pre-heating the system 4-17
STARTING SYSTEM – Dynamic description 4-18
STOPPING THE UNIT
Stopping the engine 4-22
SERVICE BRAKE – Control4 -23
PARKING BRAKE – Control4-23
5 TRANSPORT OPERATIONS
ROAD TRANSPORT
LIGHTING SYSTEM – Identification 5-1
LIGHTING SYSTEM – Control – Multifunction stalk switch 5-2
LIGHTING SYSTEM – Control 5-3
RECOVERY TRANSPORT
Preparation for towing 5-6
6 WORKING OPERATIONS
GENERAL INFORMATION
Fuel tank – Fill6-1
ENGINE – Running-in Procedure 6-2
Driving the tractor 6-2
Tractor hydraulics
PRIMARY HYDRAULIC POWER SYSTEM – Safety rules 6-3
Hydraulic power lift (HPL) 6-3
Position control 6-4
Hydraulic lift rocker6-4
HPL drop rate control valve6-4
Hydraulic manifold block/diverter valve 6-5
Rear remote control valve(s) 6-5
Rear remote valve configuration 6-5
Front remote control valve 6-6
7 MAINTENANCE
GENERAL INFORMATION
Safety rules7-1
Diesel fuel 7-2
Toolbox 7-3
MAINTENANCE CHART
Maintenance Chart 7-4
ENGINE
LUBRICATION SYSTEM – Check 7-8
LUBRICATION SYSTEM – Change fluid 7-9
FUEL AND INJECTION SYSTEM
FUEL AND INJECTION SYSTEM – Drain fluid 7-10
FUEL AND INJECTION SYSTEM – Replace 7-11
FUEL AND INJECTION SYSTEM – Bleed 7-12
FUEL AND INJECTION SYSTEM – Bleed 7-13
AIR INTAKE SYSTEM
Air cleaner – Check 7-14
Air cleaner – Cleaning Primary element 7-15
Air cleaner – Replace Inner safety element 7-16
TRANSMISSION
TRANSMISSION – Check 7-16
TRANSMISSION – Change fluid 7-17
Oil filter – Replace 7-17
Oil filter – Replace 7-18
Oil filter – Replace 7-18
ELECTRICAL POWER SYSTEM
Battery – Check 7-19
Alternator – Check 7-20
Fuse and relay box – Replace 7-21
LIGHTING SYSTEM
Head light – Replace 7-25
Taillight7-26
Turn/hazard light – Replace7-27
Cab Work Lights7-28
WHEELS AND TRACKS Wheels
WHEELS AND TRACKS Wheels – Check7-29
WHEELS AND TRACKS Wheels – Tighten 7-31
WHEELS AND TRACKS Wheels – Adjust7-32
SERVICE BRAKE
SERVICE BRAKE – Adjust 7-33
PARKING BRAKE – Adjust 7-35
FRONT AXLE
Differential – Check Front Axle Differential Case and Final Reduction Gear 7-36
Differential – Change fluid Front axle differential case and final reduction gear case oil 7-37
STORAGE
Storage – Storing – Tractor 7-39
Storage – Check – Tractor 7-40
CAB
Cab frame – Check 7-41
Seat belt – Check 7-41
ENVIRONMENT CONTROL Air-conditioning system
ENVIRONMENT CONTROL Air-conditioning system – Check 7-42
ENVIRONMENT CONTROL Air-conditioning system – Adjust 7-43
ENGINE COOLANT SYSTEM
ENGINE COOLANT SYSTEM – Check Coolant Level 7-44
ENGINE COOLANT SYSTEM – Drain fluid 7-45
Thermostat – Replace 7-46
Fan and drive Belt – Check 7-46
Fan and drive Belt – Adjust 7-47
8 SPECIFICATIONS
Consumables 8-1
Wheel tread settings 8-2
WHEELS AND TRACKS Wheels – Weight 8-3
Power Production – General Specification 8-4
FRAME AND CAB – Dimension 8-10
9 ACCESSORIES
Front ballasting – Install 9-1
Rear ballasting – Install 9-3
Wheel ballasting – Install 9-5
Grille Guard 9-6
RADIO/CASSETTE/CD PLAYER (where fitted)9-6
Two spool valve 9-6
Window grille guard 9-7
Roof Beacon 9-7
10 FORMS AND DECLARATIONS
Delivery report – Owner Copy 10-1
Delivery report – Dealer Copy 10-2
FILE DETAILS:
Case IH Tractor Farmall 40,45,50 With Cab & CVT Transmission Compact Operator’s Manual_84382269
Size : 24.2 MB
Format : PDF
Language : English
Number of Pages : 208 pages
Brand: Case IH
Type of machine: Tractor
Type of document: Operator’s Manual
Model: Farmall 40 CVT, Farmall 45 CVT, Farmall 50 CVT
Part No: 84382269
Downloadable:Yes
PLEASE NOTE:
- This is not a physical manual but a digital manual – meaning no physical copy will be couriered to you. The manual can be yours in the next 2 mins as once you make the payment, you will be directed to the download page IMMEDIATELY.
- This is the same manual used by the dealers inorder to diagnose your vehicle of its faults.
- Require some other service manual or have any queries: please WRITE to us at [email protected]
